Makita HR2410 Betriebsanleitung Seite 6

Depth gauge (Fig. 5)
The depth gauge is convenient for drilling holes of uni-
form depth. Insert the depth gauge into the hole in the
grip base. Adjust the depth gauge to the desired depth
and then tighten the clamp screw to secure the depth
gauge.
NOTE:
The depth gauge cannot be used at the position where
the depth gauge strikes against the gear housing.
Switch action (Fig. 6)
CAUTION:
Before plugging in the tool, always check to see that the
switch trigger actuates properly and returns to the "OFF"
position when released.
To start the tool, simply pull the trigger. Tool speed is
increased by increasing pressure on the trigger. Release
the trigger to stop.
Reversing switch action (Fig. 6)
For Model HR2410 and HR2410X
CAUTION:
• Always check the direction of rotation before operation.
• Use the reversing switch only after the tool comes to a
complete stop. Changing the direction of rotation
before the tool stops may damage the tool.
• Do not pull the switch trigger when the reversing switch
lever is in the neutral position. If you pull the trigger
forcibly, the switch may be damaged.
This tool has a reversing switch to change the direction of
rotation. Move the lever to the
q
rotation or the position for counterclockwise rotation.
Selecting action mode (Fig. 7)
This tool employs an action mode changing knob. Select
one of the two modes suitable for your work needs by
using this knob. For rotation only, turn the knob so that
the arrow on the knob points toward the
the tool body. For rotation with hammering, turn the knob
so that the arrow on the knob points toward the
bol on the tool body.
CAUTION:
Always set the knob fully to your desired mode symbol. If
you operate the tool with the knob positioned half-way
between the mode symbols, the tool may be damaged.
Torque limiter
The torque limiter will actuate when a certain torque level
is reached. The motor will disengage from the output
shaft. When this happens, the bit will stop turning.
CAUTION:
• As soon as the torque limiter actuates, switch off the
tool immediately. This will help prevent premature wear
of the tool.
• Hole saws, core bits, diamond core bits, etc. cannot be
used with this tool. They tend to pinch or catch easily in
the hole. This will cause the torque limiter to actuate
too frequently.
6
p
position for clockwise
M
symbol on
r
sym-
Hammer drilling operation
Position the bit at the desired location for the hole, then
pull the trigger.
Do not force the tool. Light pressure gives best results.
Keep the tool in position and prevent it from slipping away
from the hole.
Do not apply more pressure when the hole becomes
clogged with chips or particles. Instead, run the tool at an
idle, then remove the bit partially from the hole. By
repeating this several times, the hole will be cleaned out
and normal drilling may be resumed.
CAUTION:
There is tremendous and sudden twisting force exerted
on the tool/bit at the time of hole breakthrough, when the
hole becomes clogged with chips and particles, or when
striking reinforcing rods embedded in the concrete.
Always use the side grip (auxiliary handle) and firmly
hold the tool by both side grip and switch handle during
operations. Failure to do so may result in the loss of con-
trol of the tool and potentially severe injury.
Bit grease
Coat the bit shank head beforehand with a small amount
of bit grease (about 0.5 – 1 g).
This chuck lubrication assures smooth action and longer
service life.
Blow-out bulb (Fig. 8)
Use the blow-out bulb to clean out the hole.
Dust cup (Fig. 9)
Use the dust cup to prevent dust from falling over the tool
and on yourself when performing overhead drilling opera-
tions. Attach the dust cup to the bit as shown in Fig. 9.
The size of bits which the dust cup can be attached to is
as follows.
Dust cup 5
Dust cup 9
Drilling in wood or metal (Fig. 10 & 11)
Use the optional drill chuck assembly (standard equip-
ment for Model HR2410X). When installing it, refer to
"Installing or removing drill bit" described on the previous
page.
Hold the ring and turn the sleeve counterclockwise to
open the chuck jaws. Place the bit in the chuck as far as it
will go. Hold the ring firmly and turn the sleeve clockwise
to tighten the chuck.
To remove the bit, hold the ring and turn the sleeve coun-
terclockwise. Set the action mode changing knob to
"rotation only". You can drill up to 13 mm diameter in
metal and up to 32 mm diameter in wood.
Bit diameter (mm)
6 – 14.5
12 – 16