Würth master PS 350 Bedienungsanleitung Seite 15

PS 350 - GB Seite 11 Dienstag, 3. Februar 2004 1:17 13
Tool Specifications
Cross-cut Mitre Saw
Article number
Power consumption
Output power
No-load speed
Mounting bore of the saw blade
Saw blade dia. (max.)
Mitre angle, right/left (max.)
Bevel angle, right/left (max.)
Cutting depth x cutting width (max.)
- cross-cut, 90°
- mitre, 45°, bevel, 0° (left)
- mitre, 90°, bevel, 45° (left)
- mitre, 90°, bevel, 45° (right)
Dimensions
Weight (without accessories)
Protection class
Machine Elements
1 ON/OFF-switch
2 Lower blade guard
3 Stop rail, right-hand side
4 Mitre lever
5 Mitre latch
6 Mitre scale
7 Rotating table/mitre arm
8 Stop rail, left-hand side
9 Bench mounting holes
10 Base
11 Base stabiliser
12 Bevel clamp handle
13 Bevel stop screw
14 Release lever for bevel angle stop
15 Socket wrench
16 Traverse bars
17 Sawdust ejector/connection for dust extraction
18 Transport safety
19 Transport handle
20 Adjusting screws for guide-rod clearance
21 Locking screw for guide rods
22 Adjusting screw for depth stop
23 Depth stop
24 Locking screws for stop rail
25 Recess
26 Blade slot
27 Spindle lock
28 Head lock up release lever
29 Carrying handle
Not all of the accessories illustrated or described are included as standard delivery.
Symbols and Meaning
Protective insulation, protection class II
CAUTION: Danger area, "Hands off"
CAUTION: Danger area, danger of injury through the unpro-
tected saw blade
Note for adjustment of the bearing play
HKS14 Schmuck 45,0° 169,71 LPI
The machine is intended for sawing of panels, profiles, wooden laths and
PS 350
strips, as well as plastics or composite wood materials when using suitable
0701 315 X
saw blades. The machine is not suitable for sawing of metal or non-ferrous
1600 W alloys.
800 W
The user is responsible for damage caused by usage other than intended for.
4000 rpm
30 mm
305 mm
The package contains:
60°/50°
– 1 Partly assembled machine
48°
– 1 Socket wrench
– 1 Base stabiliser
91 x 305 mm
– 1 Instruction manual
91 x 216 mm
64 x 305 mm
43 x 305 mm
660 x 589 x 871 mm
Loosening the Transport Safety (see Fig. C)
27.0 kg
Press the saw head slightly downward and pull out the pin of the transport
/II
safety 18. Move the saw head upward to the starting position.
Mounting the Frame Support (see Fig. D)
Insert the frame support 11 into the two supporting bores 31. Mount the
frame support in such a manner that it rests on the supporting surface.
Tighten the screws 30. For better handling during transport, the frame
support can be slid in.
Bench Mounting
To ensure secure handling, the machine must be mounted on a suitable
support (e. g. work bench, wooden table, etc.). When mounting the ma-
chine, ensure that the workbench is standing securely.
Depending on the application, the machine can be mounted stationary or
flexible, e.g. on a Würth saw table (accessory).
The supporting points of the machine are fitted with four bores 9
(see Fig. A). Insert the fitting bolts into the bores and fasten the machine
with the corresponding nuts and washers from the bottom side.
Loosen the screw 32 and tilt the saw blade guard 34 upward.
Press the spindle lock 27 and rotate the blade by hand until you feel the
lock engage. Continue to hold the spindle lock in to keep the blade from
turning (see Fig. F).
Using the socket wrench, loosen the blade bolt 33 by turning clockwise (!).
Remove the blade bolt 33, its washer and the outer flange 35 (see Fig. E).
Press the release lever 28, move the bottom saw blade guard upward and
remove the saw blade 36.
Install the new saw blade 36 onto the shoulder provided on the inner
flange making sure that the teeth at the bottom edge of the blade are
pointing towards the fence 3/ 8 (away from the operator).
Tighten the blade bolt 33 by turning counter-clockwise (!) while holding
the spindle lock 27 engaged with your other hand.
Intended Use
Scope of Delivery
Assembly
Inserting/Replacing Saw Blades
Before any work on the machine itself, pull the plug from the
socket!
The teeth of the saw blade are very sharp and can lead to inju-
ries. Wear protective gloves when inserting or replacing the
saw blade!
Never press the spindle lock 27 while the blade is rotating.
Use only saw blades where the maximum allowable speed is at
least as high as the no load speed of the machine.
Use only saw blades that are authorized by Würth and corre-
spond with the EN 847-1 Standard.
Use saw blades that correspond to the material to be cut.
HSS saw blades (high-speed steel) may not be used.
11