Inhaltsverzeichnis
Werbung
• I t is necessary to turn on the spray lance within
one or two minutes after the machine has been
started. Otherwise, the temperature of the
circulating water within the machine will soon
rise to a critical point, which will cause damage
to the sealing rings inside the machine.
• D on't start and run the machine in a place
excessively cold so as to prevent the machine
from the freezing current.
• T his machine has been designed for only
using cleaning water, do not use corrosive
chemicals.
• U se cleaning agent supplied or recommend by
the manufacturer.
• H igh-pressure jets can be dangerous if subject
to misuse. The jet must not be directed at
persons, animals, live electrical equipment or
the machine itself. Pressure washers should
not be pointed at tire walls, as it may be
possible to damage them.
• D o not direct the jet against yourself or others
in order to clean clothes or footwear.
• D isconnect from the electrical power supply
before carrying out user maintenance.
• I f the mains cable is damaged it must be
replaced by the manufacturer, or its service
agent or similarly qualified person to avoid a
hazard.
• D o not use the machine if a supply cord or
important parts are damaged, e.g. safety
devices, high pressure hoses, trigger gun.
• B e aware of the recoil caused by the water jet
when the machine is switched on.
• W hen the machine is moving and installing,
the machine must be in flat. When moving the
machine, pulling the handle to move it.
• C onnect to the water supply. The machines are
not suitable for connection to portable water
mains. Connect the machine to the water
supply. (It can be a water container).
• M ake sure the inlet water pressure keeps
between 0.01MPa and 0.4MPa.The inlet pipe
should at least 5 M long. Do not use the pipe if
the pipe is damaged. If you want connect this
machine to portable water mains, you must
install a backflow preventer in the water pipe
to prevent dirty water flow back to the drinking
water system. The backflow preventer shall
comply with EN 60335-2-79 ANNEX AA.
6
3. ASSEMbLy ANd USE
The motor of this pressure washer will
NOT run. It will only operate when the
trigger is squeezed.
• C onnect the outlet hose to the washer and
connect the spray gun to the outlet hose.
• C onnect lance and lance extension.
• C heck gauze filter is clear of any blockage.
• C onnect the water supply hose.
• C heck that the hose has no kinks in it.
• T urn on water and check for leaks.
• S queeze trigger to allow air to be expelled
though the pump and hoses, lock trigger.
• P lug in machine and turn on switch.
• U nlock trigger and use the pressure washer.
Shut down
1. Turn off the motor (push switch to the off position).
2. Unplug the unit from the power source.
3. Turn off the water supply.
4. Press the trigger of the gun to depressurize the
system.
5. D isconnect the garden hose from the pressure
washer.
6. Wipe all surfaces of the unit with a damp clean
cloth.
7. Engage the gun safety lock.
CAUTION: ALWAYS turn off the unit's motor
BEFORE turning off the unit's water supply.
Serious damage could occur to the motor if the
unit is run without water.
CAUTION: NEVER disconnect the high-pressure
discharge hose from the machine while the
system is still pressurized. To depressurize the
unit, turn off the motor, turn off the water supply
and squeeze the trigger 2-3 times
Water supply
• E nsure that you have a suitable water supply
to feed the pressure washer. Check that all
connections are tight and there are no leaks in
the hose.
• T he supply tap should be fully open (do not
turn on the pressure washer yet).
• N ow depress the trigger (unlock trigger lock
first) to let water pass through the unit and
expel any air.
Werbung
Inhaltsverzeichnis
