Additional Safety Rules For Tool - Makita 1051D Betriebsanleitung

7. Do not incinerate the battery cartridge even if
it is severely damaged or is completely worn
out. The battery cartridge can explode in a fire.
8. Be careful not to drop, shake or strike battery.
9. Do not charge inside a box or container of any
kind. The battery must be placed in a well
ventilated area during charging.
ADDITIONAL SAFETY RULES
FOR TOOL
1. Be aware that this tool is always in an operat-
ing condition, because it does not have to be
plugged into an electrical outlet.
2. Rags, cloth, cord, string and the like should
never be left around the work area.
3. Avoid cutting nails. Inspect for and remove all
nails from the workpiece before operation.
4. Use only sharp blades. Handle the blades very
carefully.
5. Be sure the blade installation bolts are
securely tightened before operation.
6. Hold the tool firmly with both hands.
7. Keep hands away from rotating parts.
8. Before using the tool on an actual workpiece,
let it run for a while. Watch for vibration or
wobbling that could indicate poor installation
or a poorly balanced blade.
9. Make sure the blade is not contacting the
workpiece before the switch is turned on.
10. Wait until the blade attains full speed before
cutting.
11. Keep at least 200 mm away from the tool at all
times.
12. Always switch off and wait for the blades to
come to a complete stop before any adjusting.
Charging (Fig. 2)
Your new battery cartridge is not charged. You will need to charge it before use. Use the fast charger Model
DC1411 to charge the battery cartridge.
Plug the fast charger into the proper AC voltage source. The charging light will flash in green color. Insert the
battery cartridge so that the plus and minus terminals on the battery cartridge are on the same sides as their
respective markings on the fast charger. Insert the cartridge fully into the port so that it rests on the charger port
floor. When the battery cartridge is inserted, the charging light color will change from green to red and charging
will begin. The charging light will remain lit steadily on red during charging. When the charging light color
changes from red to green, the charging cycle is complete. Refer to the table below for the charging time. If you
leave the battery cartridge in the charger after the charging cycle is complete, the charger will switch into its
''trickle charge (maintenance charge)'' mode which will last approximately 24 hours. After charging, unplug the
charger from the power source.
Battery type
1422
1434
1435
6
ENB043-1
Capacity (mAh)
2,000
2,600
3,000
13. Never stick your finger into the chip chute.
Chute may jam when cutting damp wood.
Clean out chips with a stick.
14. Do not leave the tool running. Operate the tool
only when hand-held.
15. When leaving the planer, switch off and set it
with the front base up on a wooden block, so
that the blades do not contact anything.
16. Always change both blades or covers on the
drum, otherwise the resulting imbalance will
cause vibration and shorten tool life.
17. Wait for complete run-down before putting the
tool aside.
18. Use only Makita blades specified in this
manual.
SAVE THESE INSTRUCTIONS.
OPERATING INSTRUCTIONS
Installing or removing battery cartridge
(Fig. 1)
• Always switch off the tool before insertion or
removal of the battery cartridge.
• To remove the battery cartridge, withdraw it from the
tool while pressing the buttons on both sides of the
cartridge.
• To insert the battery cartridge, align the tongue on
the battery cartridge with the groove in the housing
and slip it into place. Always insert it all the way until
it locks in place with a little click. If not, it may
accidentally fall out of the tool, causing injury to you
or someone around you.
• Do not use force when inserting the battery car-
tridge. If the cartridge does not slide in easily, it is
not being inserted correctly.
Number of cells
12
12
12
Charging time
Approx. 60 min.
Approx. 75 min.
Approx. 90 min.