Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Installation and connection
Please observe the chapter "Safety instructions"!
The near field motion detector must be disconnected from the mains supply
during installation. It is not sufficient to just turn off the light switch!
First switch off all poles of the mains supply by removing the fuse or switch-
ing off at the circuit breaker and then also switch off the associated residual
current circuit breaker. Secure it against unauthorised reconnection, e.g.,
with a danger sign.
Check that the mains cable is free of current e.g. with an appropriate tester.
The controller does not have supply isolation between input and sensor out-
put. Therefore, ensure suitable touch protection for the control unit of the
close-range motion detector and the connecting cable between the sensor
unit and the control unit when installing and mounting. After installation, it
should only be possible to touch the front of the sensor unit.
• Make sure you fix the near field motion detector to a solid base, e.g. masonry. Use
screws and, if necessary, screw anchors that are suitable for the surface.
Caution!
Pay attention when drilling and tightening the screws that no cables or pipes
are damaged!
• The sensor unit only requires a borehole with a diameter of approx. 14 mm.
Do not install the sensor unit behind glass. The front of the sensor unit must
not be obstructed.
• Connect the 3-pin plug at the end of the cable of the sensor unit with the corre-
sponding socket of the near field motion detector.
• Remove the screw for the cable clip cover and then remove the cover.
• Remove the outer insulation of the power cable and of the connection cable to the
consumer load for a length of 10 mm.
Then, remove the insulation of the single wires for a length of 5 mm.
• Connect the power cable and the connection
cable to the consumer load; observe the inscrip-
tion on the housing of the near field motion detec-
tor or the image on the right.
• Attach the cable clip cover and secure it with the corresponding screw.
The cable clip cover also serves as fixation and pull relief for the power
cable and for the connection cable to the consumer load.
• Switch on the power. The near field motion detector is now ready for use.
As a test, hold one hand in front of the sensor unit (max. distance approx.
5 - 6 cm). The consumer load must now be switched on.
Remove your hand from the sensor unit and hold it in front of the unit again.
The consumer load is switched off.
Maintenance and cleaning
The product is maintenance-free. Repair or maintenance work must be carried out
by a specialist.
Use a clean, soft, dry cloth for cleaning the front of the sensor unit. Dust at the front
of the sensor unit can be very easily removed with a soft, clean brush and a vacuum
cleaner.
Do not use aggressive, chemical or scouring cleaning agents, as this may lead to dis-
colouration or changes in the material on the surface.
Disposal
The product must not be disposed of in the household waste.
Dispose of the product at the end of its serviceable life in accordance with
the current statutory requirements; e.g. return it to any suitable collection
point.
Technical data
a) Near field motion detector
Operating voltage.....................................110 - 240 V/AC, 50/60 Hz
Switching power at 220 - 240 V/AC .......500 W (resistive load)
.....................................................................200 W (inductive load)
Switching power at 110 - 130 V/AC .......300 W (resistive load)
.....................................................................100 W (inductive load)
Devices with mainly resistive load are e.g., light bulbs, heaters, etc.
Devices with inductive load are, e.g., engines, control gears, conventional
transformers, energy saving bulbs, etc.
Switch type ...............................................Relay; single-pole
Protection type .........................................IP20
Dimensions................................................88 x 35.5 x 20.5 mm (L x W x H)
Weight ........................................................approx. 40 g
b) Sensor unit
Detection distance...................................max. approx. 5 - 6 cm
Installation hole diameter .......................14 mm
Mounting depth ........................................16 mm
Exterior diameter......................................17.2 mm
Cable length ..............................................approx. 145 cm
Weight ........................................................approx. 17 g (incl. cable)
c) General
Installation location ................................. only in dry, enclosed indoor locations
Operating conditions ...............................Temperature -20 °C to +50 °C
.....................................................................
L
N
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data
processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication represent
the technical status at the time of printing.
© Copyright 2016 by Conrad Electronic SE.
Humidity 0% to 93% relative air humidity, non-
condensing
Werbung
Inhaltsverzeichnis
