Package Contents; Safety Instructions - Renkforce 1289332 Bedienungsanleitung

G Operating instructions
Near Field Motion Detector
Item no. 1289332
Intended use
The near field motion detector with an IR LED and and an IR sensor detects move-
ments near the sensor (max. distance approx. 5 - 6 cm), e.g. when holding your hand
in front of the sensor.
An electric consumer load (e.g. a lamp) can be controlled using the output of the near
field motion detector. Observe the maximum connected load in the chapter "Technical
data".
The product is only suitable for installation and operation in dry, closed indoor loca-
tions. It must not get damp or wet.
Always observe the safety instructions included in these operating instructions.
Please read the operating instructions carefully and keep them.
Any use other than the one described above could lead to damage to this product and
present a hazard of short circuits, fire, electric shock, etc. No part of the product may
be modified or converted!
This product complies with the applicable national and European requirements. All
names of companies and products are the trademarks of the respective owners. All
rights reserved.

Package contents

• Near field motion detector
• Sensor unit with connection cable
• 2 screws
• Operating instructions
Up-to-date operating instructions:
1. Open www.conrad.com/downloads in a browser or scan the
displayed QR code.
2. Select document type and language and enter the item num-
ber into the search field. After submitting the query you can
download displayed records.
Explanation of symbols, inscriptions
The lightning symbol inside a triangle is a warning to inform you of potential
risks of personal injury, such as electric shock.
This symbol indicates specific risks associated with handling, operation or
use.
The arrow symbol indicates special tips and operating information.
The product is only intended to be installed and used in dry, indoor rooms; it
must not get damp or wet.
Observe the operating instructions!

Safety instructions

Read the complete operating manual carefully before using the product, as
it contains important information about the proper installation and opera-
tion.
Damage due to failure to follow these operating instructions will void the
warranty! We do not assume any liability for any resulting damage!
Warning!
The product may be installed only by a qualified technician (electrician)
who is familiar with the relevant regulations (e.g., VDE, German electrical
wiring regulations)!
Improper work carried out on the mains voltage endangers not only your
own life, but also the life of others!
If you do not have the expertise required for the installation, do not install it
yourself but ask a qualified technician.
• Unauthorised conversion and/or modification of the product is not al-
lowed for safety and approval reasons (CE).
• The product is not a toy and does not belong in the hands of children!
There is danger of a life-threatening electric shock!
• The product may be operated only on the mains voltage (see section
"Technical data"). Never try to operate the product at another voltage, as
this will result in destruction of the product.
• During installation, all poles must be disconnected from the mains voltage
(e.g., via RCD).
• The product may be installed and used only in dry indoor spaces; it must
not get damp or wet. There is danger of a life-threatening electric shock!
• Only install and use the product when it is firmly mounted.
• The controller does not have network isolation between input and sensor
output. Therefore, ensure suitable touch protection for the control unit of
the close-range motion detector and the connecting cable between the
sensor unit and the control unit when installing and mounting. After instal-
lation, it should only be possible to touch the front of the sensor unit.
• Do not use this product in rooms that are under adverse environmen-
tal conditions where combustible gases, vapours or dust are or may be
present! There is a risk of explosion!
• The product must not be exposed to extreme temperatures, strong vibra-
tions or heavy mechanical stress.
• If it can be assumed that safe operation is no longer possible, the device
must be turned off and precautions must be taken to ensure that it is not
used unintentionally. After this, arrange for an expert to check the product.
Safe operation can no longer be assumed if:
- the product shows visible signs of damage
- the product does not work at all or works poorly (where there is flicker-
ing light, leaking smoke or a smell of burning, audible crackling noises,
or discolouration of the product or to adjacent surfaces)
- the product was stored for a longer period of time in unfavourable condi-
tions
- it was exposed to heavy loads during transport
• Do not leave packaging material carelessly lying around, since it could
become a dangerous plaything for children.
• In commercial institutions, the accident prevention regulations of the Em-
ployer's Liability Insurance Association for Electrical Systems and Operat-
ing Facilities are to be observed!
• If you have any questions that are not answered in these operating in-
structions, please contact our technical department or another specialist.
Function of the near field motion detector
An IR LED inside the sensor unit of the near field motion detector emits light that is
invisible to the human eye.
If an object (e.g. a hand) appears in front of the sensor unit, this light is reflected to
an IR sensor.
Then, the near field motion detector switches the connected electric consumer load
(e.g. a lamp) on.
The range for detecting of a movement is dependent on the reflecting prop-
erties of the surface and the distance of the object from the sensor unit.
Generally, the maximum distance is 5 - 6 cm. Larger distances are possible
for highly reflective surfaces.
Due to these specialities, the near field motion detector can be used as contact-less
switch.