Shutting Down The Appliance . En; Grey Intelligent Key - Kärcher B 60 W Bp Bedienungsanleitung

– Power Clean: High brush speed for pol-
ishing, crystallising and sweeping.
 Turn the program selection switch to
the desired cleaning program.
 Turn the info button until the desired pa-
rameter is displayed.
 Press Info button - the set value blinks.
 Set the desired value by turning the info
button.
 Confirm the changed setting by press-
ing the Info button or wait till the set val-
ue is automatically accepted after 10
seconds.
Cleaning
ATTENTION
Risk of damage to the floor covering. Do
not operate the appliance on the spot.
 Turn the program selection switch to
the desired cleaning program.
Lower the cleaning head
 Press the pedal for lowering the clean-
ing head downwards slightly and then
move it to the left. This unlocks the ped-
al. Release the pedal slowly upwards.
The cleaning head is lowered.
Note:
The brush motor comes to a halt when the
machine stops and when there is overload.
Adjusting the brush contact pressure
 Arrest the lever in the desired position.
Upper position: higher contact pressure
Lower position: reduced contact pres-
sure
Lower the vacuum bar
 Pull the lever out and press it down; the
vacuum bar is lowered.
Note:
– For cleaning tiled floors, adjust the
straight suction bar in such a way that
cleaning is not done at an angle of 90
degrees to the joints.
– The inclined position and the inclination
of the suction bar can be adjusted to
achieve better suction results (see "Ad-
justing the suction bar").
– If the wastewater reservoir is full, the
floater will close the suction opening
and the suction turbine will run at a
higher speed. If this is the case, shut
the vacuum off and drive to empty the
wastewater reservoir.
Shutting Down the Appliance
 Close the regulatory button for setting
the water quantity.
 Release drive lever/safety switch.
 Set the program selection switch to suc-
tion or vacuuming.
 Lift the cleaning head.
 Briefly drive forward and suck of the re-
maining water.
 Raise the vacuum bar.
The suction turbine will continue to run
for 10 more seconds to suck off residual
water from the vacuum bar and the vac-
uum hose.
 Remove the Intelligent Key.
 Charge battery, if required.
18
Drain off dirt water
WARNING
Please observe the local provisions regard-
ing the wastewater treatment.
 Take the water discharge hose from the
support and lower above a suited col-
lection device.
 Crush or bend the dosing equipment.
 Open the lid of the dosing equipment.
 Drain off the dirt water - regulate the
water quantity by pressing or bending.
 Rinse the waste water tank with clean
water or with the rinsing system for the
waste water tank (option).
Drain off clean water
 Loosen the lid for emptying the fresh
water slowly - do not remove it fully.
For a quicker emptying process, re-
move the entire lid.
 To rinse the fresh water reservoir, re-
move the cover completely and remove
the fresh water filter.

Grey Intelligent Key

 Plug in the Intelligent Key.
 Select the desired function by turning
the Info button.
The different functions are described in the
following.
Key menu >>
In this menu item, the authorisations for the
yellow Intelligent Keys are released.
 Press the info button while "Key menu
>>" is displayed.
 Remove the grey Intelligent Key and in-
sert the yellow Intelligent Key to be pro-
grammed.
 Select the desired menu item to be
modified by turning the Info button.
 Press Info button.
 Adjust the menu item by turning the Info
button.
 Confirm the setting by pressing the
menu item.
 Select the next menu item to be modi-
fied by turning the Info button.
5
-
EN
 To save the authorisations, retrieve the
menu "Save settings" by turning the info
button and pressing it.
 To exit, retrieve the menu "Exit menu"
by turning the info button and pressing
it.
Cleaning App >>
Parameters that are adjusted with the grey
Intelligent Key, are kept until another set-
ting is selected.
 Turn the program selection switch to
the desired cleaning program.
 Turn the info button until "Cleaning App
>>" is displayed.
 Press the info button - the first adjusta-
ble parameter is displayed.
 Press Info button - the set value blinks.
 Set the desired value by turning the info
button.
 Confirm the changed setting by press-
ing the Info button or wait till the set val-
ue is automatically accepted after 10
seconds.
 Select the next parameter by turning
the Info button.
 After all desired parameters have been
modified, turn the info button until "Exit
menu" is displayed.
 Press the info button - you will exit the
menu.
Setting the language
 Press Info button - the set value blinks.
 Set the desired language by turning the
info button.
 Confirm the changed setting by press-
ing the Info button or wait till the set val-
ue is automatically accepted after 10
seconds.
Brush trailing
Adjust the trailing time of the brushes.
 Same adjustment as "Set language".
Setting the charging marker line
 Turn the info button until the function
"Battery menu" is displayed.
 Press the info button - select the charg-
ing marker line according to the built-in
batteries.
Note: Setting the charging marker line
should be discussed with Kärcher cus-
tomer service. This applies especially if
the battery is not listed in the menu.
 Confirm the changed setting by press-
ing the Info button or wait till the set val-
ue is automatically accepted after 10
seconds.
LOAD DEFAULT
Recreate the basic settings.