Operation - EINHELL BT-BD 801 E Bedienungsanleitung

6.3. Folding chip guard (Figs. 15 - 17)
Mount the folding chip guard (13) as shown in
Figures 15 and 16.
The height of the cover (23) is infinitely
adjustable and can be locked using both thumb
screws (22). The chip guard (13) can be flipped
up to enable bits to be changed.
6.4. Prior to starting
Ensure that the voltage of the mains supply complies
with the specifications on the rating plate. Connect
the machine only to a socket with the properly
installed earthing contact.
The table drill is equipped with a no-volt trip that is
designed to protect the operator from an undesired
restart following a drop in voltage. Should this occur,
the machine must be manually restarted.

7. Operation

7.1. General (Fig. 18)
To switch on the machine, push in the green On
button "I" (18); the machine starts up. To switch
off, press the red Off button "O" (19); the device
shuts down.
Ensure that you do not overload the device.
If the sound of the motor drops in pitch during
operation, it is being overloaded.
Do not overload the device to the point where the
motor comes to a standstill.
7.2. Inserting the tool (Fig. 1)
Make sure that the power plug is removed from the
socket-outlet before changing tools. Only cylindrical
tools with the stipulated maximum shaft diameter
may be clamped in the scroll chuck (10). Only use a
tool that is sharp and free of defects. Do not use
tools whose shaft is damaged or which are deformed
or flawed in any other way. Use only accessories and
attachments that are specified in the operating
instructions or have been approved by the
manufacturer.
7.3. Handling the keyless chuck
Your pillar drill is equipped with a keyless chuck. This
enables tools to be changed without the need for an
additional chuck key. To do so, insert the tool in the
quick-change drill chuck and tighten by hand.
7.4 Using tools with tapered shanks (Fig. 19)
The pillar drill comes with a spindle taper.
To use tools with tapered shanks (MK2), proceed as
follows:
Move the drill chuck to the lower position.
Lock the spindle in the lowered position using the
bottom scale ring (25) to maximize access to the
drill chuck (see point 7.6).
Eject the tapered shank using the supplied drill
drift (31), taking care as you do so to ensure that
the tool does not land on the floor.
Insert the new tool with tapered shank in the
spindle taper with a jolt and then check that the
tool is correctly seated.
7.5. Setting the speed (Fig. 1)
The operating speed of the machine is infinitely
adjustable.
Important!
Speed adjustments are allowed only when
the motor is running.
Slowly and steadily move the speed control
lever (15) while the machine is in idle mode.
Ensure that the machine can run without
interruption (i.e. remove workpieces, drill
bits, etc.).
Use the speed control lever (15) to infinitely adjust
the speed. The set speed is shown on the digital
display (17) in revolutions per minute.
Important! Never let the pillar drill run when the V-
belt cover is open. Always pull power plug before
opening the cover. Never touch the V-belt when it is
rotating.
7.6 Drill depth stop (Fig. 20/Item 14)
The drilling spindle has a swivelling scale ring for
setting the drill depth. Only adjust the setting when
the machine is at a standstill.
Press the drilling spindle (11) downwards until
the tip of the drill bit touches the workpiece.
Turn the scale ring (25) all the way down.
Turn the scale ring (25) up by the distance of the
desired drill depth and lock the setting with the
second scale ring (25).
The highest setting of the drilling spindle can
likewise be adjusted using the bottom scale ring
(practical when ejecting the drill chuck (see point
7.4).
GB
17