Parts Identification; Operation; Maintenance - Panasonic er2301 Gebrauchsanleitung

B461518_ER2301_Tori_EU
This Beard/Hair Trimmer is for the
trimming and care of mustaches,
beards and hair.Trimming length
can be adjusted between 2 to
1 8 m m . T h e T r i m m e r c a n b e
operated either from an AC power
source or on its own rechargeable
battery.

Parts identification

(See Fig. 1)
Switch
A
Slide up to turn on, slide down
to turn off.
Charging Indicator Lamp
B
Lights when the unit is con-
nected with the adapter
AC power source for charging.
Main Blade
C
A precision 39mm-wide blade
which can be used with the
comb attachment
Thinning Plate
D
When thinning,slide the thinning
plate up until it firmly clicks in
position. (See Fig. 2)
Thinning Plate Lock Button
E
Press and hold while sliding the
Thinning plate
D
the Thinning Plate back to its
original position.
Dial
F
Turn the dial to a higher set-
ting to raise or lower the comb
attachment to the desired
G
length (between 2 and 18mm).
Comb Attachment
G
Use this to control the trimming
length. (See Fig. 4) Be sure to
slide the Thinning plate down to
"1" before attaching the attach-
ment. (See Fig. 3)
Stationary Blade
H
Moving Blade
I
Refine_P00-07_EN_ER2301_004.p1.pdf
Refine_08-04-04 10:36:40
P00-07_EN_ER2301.indd 4 P00-07_EN_ER2301.indd 4
Cleaning Lever
J
Push this lever to remove bits of
hair caught between the station-
ary blade and the moving blade.
Blade Block
K
Release to remove the blade
block from the housing to clean
or replace the blade. (See Fig.
9)
Adapter
L
Use this to connect the Trimmer
to an AC power source for re-
charging or for AC operation.
Oil
M
Lubricate the space between
the stationary and moving blade
to an
L with 2 or 3 drops of oil after use.
(See Fig. 11)
Cleaning Brush
N
.
Trimming length indicator
G
Indicator Trimming Length
1
●
2
down to set
●
3
●
4
●
5
●
6
●
4
3 08-04-23

Operation

Rechargeable-battery operation
Charge the battery by plugging the
Trimmer into an AC source using
the adapter. The switch should be
set to 0·CHARGE during charging.
An 8-hour charge will provide ap-
prox. 30 minutes of use.
AC operation
Plug the Trimmer into an AC power
source using the adapter with the
switch set to 0·CHARGE.Wait
about 10 seconds, then switch the
trimmer on. After use, return the
switch to the 0·CHARGE position.
Trimming of Beard
Place the angled face of the comb
against the skin and cut the beard
by moving the trimmer in all direc-
tions to obtain a uniform cut. (See
Fig. 5)
With curly facial hair, the comb
attachment may not cut all of the
2.0mm
hair. In this case, remove the comb
3.0mm attachment and use a conventional
comb to draw out the remaining
4.5mm
uncut hair.
(See Fig. 6)
6.0mm
When shaping the beard, remove
the comb attachment. Place the
7.5mm
angled edge against the skin and
9.0mm make the border of the beard even.
How to use the thinning function
10.5mm
(See Fig. 7)
12.0mm
First, slide the Thinning plate up
to "1/3" until it clicks. (See Fig. 2)
13.5mm
While applying the blade point at
15.0mm right angles to the hair, run the
trimmer slowly across the head as
16.5mm
if combing the hair. After thinning,
slide the thinning plate back while
18.0mm
pushing the Thinning Plate Lock
Refine_P00-07_EN_ER2301_005.p1.pdf
Refine_08-04-04
P00-07_EN_ER2301.indd 5 P00-07_EN_ER2301.indd 5 2008/04/04 10:31:25 2008/04/04 10:31:25
11:30:19
Button. (See Fig.3)
Notes on thinning
For thinning, confirm that the thin-
ning plate is set to the 1/3 (right)
position.Incorrect setting may result
in excessive cutting.
If a difference in level is produced,
lightly thin to compensate.
If thick and thin portions are pro-
duced, or if there are portions with
an excessive amount of hair, thin
the appropriate portions to com-
pensate.
Point:
Thin the hair gradually while check-
ing the overall balance.

Maintenance

Blades
1. Brush out the cutting mecha-
nism. (See Fig. 8)
2. Hold body of the trimmer with
Panasonic mark upwatds, place
the thumb against the blades,
and push them away from the
main body. (See Fig. 9)
3. Push down the cleaning lever
to raise the moving blade and
brush in between the blades.
(See Fig. 10)
4. Put a few drops of oil on the
blades. (See Fig. 11)
Blade Life
Blade life will vary according to
the frequency and length of use.
For example, using the unit for 10
minutes every 3 days, the life ex-
pectancy is approximately 3 years.
If cutting efficiency is reduced sub-
stantially despite proper mainte-
nance, the blades have exceeded
their service life and should be
changed. The replacement part
no. is ER965.
5
10:36:40
2008/04/04 10:31:26 2008/04/04 10:31:26