Herunterladen Inhalt Inhalt Diese Seite drucken

Grundig 5300 RDS Betriebsanleitung Seite 10

Inhaltsverzeichnis

Werbung

Amplifier
Switching on and off on the car radio
ASP (Audio Sound Processing)
Briefly press the
¢ ¢
rotary knob.
Using the Audio Sound Processing system,
you have the choice between various space
sound effects.
Switching on for 1 hour max.
The first four station buttons are allocated to
... after you have switched your car radio
the sound effects "MOVIE", "DISCO", "VOI-
off with the ignition/starter switch of your
CE", and "MUSIC".
vehicle:
Pressing the station button
Press the
¢ ¢
rotary knob.
function.
The display indicates "ASP OFF".
If the ignition/starter switch remains off, the
car radio switches off automatically after
1 hour.
Volume
¢ ¢
Turn the
rotary knob.
"
A S P
The display indicates:
¢ ¢
MONO
"VOL 00" ... "VOL 46"
LOUD (loudness)
This function improves the sound quality at
low volume levels.
Loudness on/off
"
LOUD
Briefly press the
button.
EXPERT
With "Loudness" on, the display indicates
"
BA
FAD
"LOUD".
Radio
Amplifier
Overload protection
Selecting the RADIO programme source
At high ambient temperature and volume, the
In cassette or CD mode:
¡
overload protection circuit may respond.
briefly press the
RADIO
button.
As long as the overload is not removed, the
rear output stages of the amplifier are swit-
Range selection
ched off.
¡
Repeatedly press the
RADIO
U ranges U l, U ll, U lll (FM):
VHF 87.5 ... 108.0 MHz
To switch between the U ranges:
repeatedly and briefly press the
button.
MW range: Mediumwave 531...1602 kHz
LW range: Longwave 153 ... 279 kHz
¡
¡
¡
RADIO
L RN/AS
P TY/DX
"
A S P
<
"
1
5
¡
TP
U III
MONO
"
A S P
Briefly press the
.button.
MONO
Use the station buttons
1
to
4
to select the
desired sound effect.
The display indicates, for example, "MUSIC".
í
In the case of mono broadcasts, or when
selecting mono manually, you will percei-
ve a sound effect only when selecting
5
exits the ASP
"VOICE".
When you are in a zone of poor reception,
using the ASP function may increase recepti-
on distortions. If this should be the case,
switch off the ASP function.
"
LOUD
EXPERT
"
TRE
1
5
BAL
After selecting the range:
you will hear the station last tuned to in this
range (Last-station-memory).
Stereo reception (VHF only)
You are receiving a stereo broadcast if the
display indicates "
".
button.
Manually switching to mono:
"
A S P
Press the
button until the signal
MONO
¡
U III
sounds. The ASP function is only effective in
the "VOICE" position.
" " appears in the display.
"
A S P
Switching back to stereo: press the
MONO
button until the signal sounds.
>
TRE (Treble)
BASS
"
"
TRE
BA
Briefly press the
button.
Briefly press the
button.
FAD
BAL
Turn the
¢ ¢
rotary knob.
Turn the
¢ ¢
rotary knob:
The display indicates:
The display indicates:
"TREB - 14"..."TREB 00"..."TREB + 14"
"BASS - 8"..."BASS 00"..."BASS + 8"
Terminate the setting:
Terminate the setting:
"
"
TRE
BA
Briefly press the
button two times, or
Briefly press the
button two times,
BAL
FAD
or automatically after approx. 10 seconds.
automatically after approx. 10 seconds.
Immediate median position:
Immediate median setting:
"
BA
Press the
button until the signal
"
FAD
TRE
Press the
button until the signal
BAL
sounds.
sounds.
FAD (Fader)
BAL (Balance)
Front
rear loudspeaker
Left
right loudspeaker.
"
BA
Briefly press the
button two times.
"
TRE
FAD
Briefly press the
button two times.
BAL
Turn the
¢ ¢
rotary knob:
Turn the
¢ ¢
rotary knob.
The display indicates:
The display indicates:
"FAD F31" ... "FAD R - - F" ... "FAD R31"
"BAL L31"..."BAL L - - R"..."BAL R31"
Front
Median position
Left
Median position
Right
Terminate the setting:
Terminate the setting:
"
BA
Briefly press the
button, or automati-
"
FAD
TRE
Briefly press the
button, or automati-
BAL
cally after approx. 10 seconds.
cally after approx. 10 seconds.
Immediate median position:
Immediate median position:
"
BA
Press the
button until the signal
FAD
"
TRE
Press the
button until the signal
sounds.
BAL
sounds.
– automatically (AUTOSCAN)
Setting RDS programmes with the
¡
Press the
RADIO
button until the signal
LEARN memory
sounds.
With the push of a button
"AUTOSCAN" appears in the display.
you can store up to 24 RDS programmes in
After that all RDS programmes are called up
one after the other for approx. 10 seconds.
the LEARN memory!
You can call up the stored RDS programmes
If the called up station is to be maintained,
manually (RDS-SCAN) or automatically
¡
briefly press the
RADIO
button.
(AUTOSCAN) one after the other.
"RESET" appears briefly in the display.
Allocating the LEARN memory
Automatic station store
Ranges: U I, U II or U III.
¡
Briefly press the
button:
Autostore
L RN/AS
RDS programmes (max. 24) being received in
The 5 strongest stations of the selected
the reception area are stored in memory.
range received in your reception are are
"LRN ..." appears in the display .
automatically stored in the station
After storing you will hear the RDS program-
1
4
buttons
me having the best reception quality or only
RDS programmes with traffic announcements
Select the desired range: U I, U II, U III, MW
if the
"
button has been "activated".
TP
or LW.
"
On/off: press the
TP
button.
¡
Press the
L RN/AS
button until the signal
– manually (RDS–SCAN)
sounds.
<
>
(Repeatedly) briefly press the
or
button:
The display indicates "AS" and the frequency
"RDS SCAN" appears in the display.
scrolls on the display.
After that you hear the next RDS programme.
After that you hear the programme having the
best reception quality.
Amplifier
Tone memory
It is possible to store various sound and
fader/balance settings by means of the station
1
2
buttons
.
Storing settings
Set the bass, treble, fader, balance, and
loudness as desired.
When you are in one of the various setting
modes, press, for example, the station
1
button
until the signal sounds.
The display indicates "SOUND 1".
The set values are stored in memory.
Calling up settings
"
"
BA
TRE
Press the
or
button and then,
FAD
BAL
1
for example, briefly press the station button
.
"
"
BA
TRE
Pressing the
or
button and then
FAD
BAL
1
the station button
,calls up the linear (medi-
an) settings.
Rear
The display indicates "LINEAR".
Radio
Setting stations/RDS programmes with
the search function
Select the desired range: U I, U II or U III.
<
>
Press the
or
button until the signal
sounds.
The display indicates, for example,
"FM 92.70".
The search stops at the next station or RDS
programme.
The search function is set to maximum
sensitivity if
"DX" appears in the display.
– This occurs automatically after the first scan
of the entire frequency range.
– Switching manually to "DX":
¡
press the
P TY/DX
button until the signal
sounds.
– Switching off "DX" :
press the
¡
button until the signal
P TY/DX
sounds.
Only stations/RDS programmes with traffic
announcements are searched if
"
the
TP
button is "activated".
"
On/off: press the
button.
TP

Werbung

Inhaltsverzeichnis
loading

Diese Anleitung auch für:

5600 rds

Inhaltsverzeichnis