Inhaltsverzeichnis
Werbung
CONTROLS
BACK SIDE of MAX
DISPLAY
AC MAINS - socket for mains lead
The display shows:
Car battery socket – Use the provided car battery
FM stereo stations
connection cable for connection to a car battery.
Voltage selector switch – For switching the mains
mally tuned to a radio
power supply voltage.
station
For FM reception the frequencies are indicated in MHz and
REMOTE CONTROL
for MW reception in kHz.
88
Changing the batteries
messages are displayed
If the range of your infrared
remote control seems to
TIME – when track time is indicated
decrease, or if certain
REMAIN TIME – when the remaining track time is
individual functions can no
indicated.
longer be carried out, you
STBY/ON
STBY/ON
TOTAL REMAIN TIME – when the total remaining time
should replace the batteries.
of the CD is indicated.
Two mignon 1.5 Volt LR03
SCAN – during the INTRO function
size AAA are required. To
RANDOM – during random playback of a CD
change the batteries, open
REPEAT – during the CD repeat function.
the compartment on the back
MEMORY – during CD programming, playback of a CD
of the remote control. Ensure
program or when tuned to a memorized radio station.
STATION
STATION
that the batteries are inserted
properly (note the markings
POWER SUPPLY
in the compartment).
VOLUME
VOLUME
Mains supply
And in the interest of the
• Check if the mains voltage as shown on the type plate (on the
environment: Remember that
bottom of the set) corresponds to your local mains voltage.
batteries must always be
If it does not, consult your dealer or service
disposed of properly.
organisation.
• Connect the mains lead to the MAINS socket and the
wall socket. The mains supply is switched on.
• Note: Even if you switch your unit off, it remains
connected to the mains power supply. The red standby
LED at the upper left side of the display is always on
when the unit is connected to the mains power supply.
• To disconnect the set from the mains completely,
withdraw the mains plug from the wall socket.
y STBY/ON – To switch the system on and to stand by.
• Remark: As this is a high-powered product, please use
S / T – Press briefly to select next or previous CD
whenever possible the mains supply to save battery life.
tracks. Keep pressed to search for a certain CD passage.
Battery supply
B; – To start and to interrupt CD playback.
• Release the POWER PACK on
the top of MAX by pushing the
9 – To stop CD playback.
two knobs to the side (as
STATION 3 4 – To select memorized radio stations
indicated 1 and 2).
VOLUME 3 4 – To adjust the volume
– The POWER PACK jumps out.
• Insert as shown 8 batteries, type
R20, UM1 or D-cells.
• Remove the batteries if exhaus-
ted or if they will not be used
again for a long period.
The battery supply is switched
off when the set is connected to
the mains. To change over to
battery supply, pull out the plug
from the MAINS socket.
POWER SUPPLY
– when receiving
– if the unit is opti-
FM
kHz
MW
MHz
8888
– in this part of the display all relevant
8
– indicates the output signal
8 x D-cells - R20 - UM1
GENERAL
SWITCHING ON AND OFF
RADIO AERIALS
– For FM, pull out the telescopic aerial. To improve FM-
• Press the POWER knob to switch MAX on.
reception, incline and turn the aerial. Reduce its length if
– Max will be activated and the source that was chosen
the FM-signal is too strong (very close to a transmitter).
before the power was switched off will be selected again.
– For AM/MW, the set is provided with a built-in aerial, so
• To switch the unit off press the POWER button again.
the telescopic aerial is not needed. Direct the aerial by
turning the whole set.
STAND BY
RADIO RECEPTION
• You can switch the system to STAND BY with the
y STBY/ON key on the remote control.
• Press the AM/FM button on the unit, or one of the
– Active STAND BY mode is indicated by the indication
STATION 3 4 buttons on the remote control.
'Stdb
' on the display:
Y
• Press the AM/FM button to select the wave band.
• When you want to switch your system on again, simply
• Start the automatic station search by holding the
press y STBY/ON again or one of the following keys
TUNING 3 or 4 button down for one or two seconds,
on the unit or on the remote control: 9, B;, INTRO,
and then releasing it.
RANDOM, STATION 3 4, TUNING 3 4, AM/FM,
– The tuner automatically
CD or TAPE.
searches for the first
station with sufficient
SOURCE SELECTION
signal strength.
• Repeat this step to search for other stations.
• Select a source by pressing CD, FM/AM or TAPE.
• To tune to a weak station, briefly press the TUNING 3
– Your unit is also equipped with a function that automati-
4 buttons several times until the correct frequency is
cally selects the correct sound source in accordance
displayed, or until reception quality is best.
with the button you press.
For example, if the unit is in the radio mode and you
• Adjust the sound using VOLUME, Tone Control and
press B; (CD play button), the unit automatically
UBS.
switches to the CD play mode.
STORING STATIONS
– The buttons for automatic sound source selection when
using the radio are STATION 3 4, TUNING 3 4, and
You can store a maximum of 15 stations.
FM/AM.
• Press the AM/FM button to select the wave band.
– The buttons for automatic sound source selection when
• Select the desired station by pressing the TUNING 3
using the CD player are 9, B;, INTRO and
4 buttons.
RANDOM.
• If you press the MEMORY button, the frequency of the
– This automatic sound source selection is not available
station you have set is stored in the next available
for cassette mechanism keys.
memory position.
– 'FULL' appears in the display for approx. 8 seconds
SOUND CONTROL
when the memory is full.
Volume
CLEARING STORED STATIONS
• The volume can be adjusted with the rotary VOLUME
controller.
• Select the stored station and briefly press the CANCEL
• The volume can also be controlled via the remote
to remove the stored station from the memory.
control with the VOLUME 3 4 buttons.
Tone control
SELECTING STATIONS
• Adjust the sliding controls for Bass (100 Hz), mid-tone
• Select a number between 1 and 15 by pressing the STATION
(1 kHz) and Treble (10 kHz) adjustment
3 or 4 button on the unit or on the remote control.
Ultra Bass System
– The station´s memory
• If desired you can press the UBS button several times to
number, the frequen-
increase the bass effect. Every time you press the UBS
cy, and the wave band
button the value changes as follows: 0 db--> 2 db-->
are shown on the
4 db--> 6 db--> 9 db--> 12 db--> 9 db--> etc.
display, and the unit
selects the displayed station.
• If no stations are stored, the indication 'MEMORY 00' is
blinking on the display for approx. 1 second.
RADIO
FM
MHz
FM
MHz
Werbung
Inhaltsverzeichnis
