Inhaltsverzeichnis
Werbung
AT A GLANCE
_________________________________________________________________________
The remote control
Switches the satellite TV receiver in standby mode and from standby to the last
selected channel position (last station memory).
Switches the sound off and on again; a symbol »
0
the screen as long as the sound is muted.
1
2
3
0 ... 9
Digit buttons for channel position selection (in standby mode too) and for entering
4
5
6
data in the menus.
7
8
9
Switching between favourite mode and normal mode with »F« (the next highest
or lowest channel position is switched with
P
+
In the operating menus: Fade in blue screen background and fade out again.
–
OK
Superimposes the status information on the screen (for a few seconds).
P
You may call up the three menus with »
is superimposed.
SRC 5
In the menus » 1... 3«: Exit menu without saving.
Select channel position step by step.
P+ P-
Switching on from standby mode. In the menus » 1... 3«: Select the menu items.
-
+
Adjust volume.
In the sub-menus: Select the channel position number step by step;
Change values.
OK
In the menus » 1... 3«: Save settings (afterwards the corresponding menu is auto-
matically faded out).
SETTINGS
______________________________________________________________________________
Status display
1
Status display fade in on screen with » «.
?
?
300
– The status display is superimposed for a short time.
11.494 GHZ
$
V–A
Explanations:
7.02 MHZ 7.20 MHZ
»300
«
~
PANDA
»
11.494 GHZ
«
»
V–A
«
$ $
16:35
1:
2: ?
? 3:
»
7.02 MHZ 7.20 MHZ
»
~
PANDA«
»
16:35«
2
The desired menu can be super imposed with
appears.
Explanations:
»
1:
2:
?
?
3:
«
Note:
The time can be set in the timer menu. The other settings (transmission frequency, LNC setting,
sound settings) are carried out in the »channel position settings« menu.
« appears at the top right of
»P+
P-«).
« as long as the status information
1... 3
Channel number
satellite transmission frequency
LNC setting: Polarisation V/H,
22 kHz switching frequency off (–)/on (~), satellite selection
A/B
« left and right audio frequency
deemphasis/noise suppression
time
»1...3
« as long as the status display fade in
» «
Status display fade out
»1:
«
Timer menu fade in
»2:
?
?
«
»Channel position settings« menu fade in
»3:
«
»System settings« menu fade in
SETTINGS
___________________________________________________________________________
Button functions in menu mode
Use the remote control buttons for all settings or changes in the menu.
The following button functions are the most frequent used in menu operation (these button functions
are not always referred to in the individual menu settings).
– If the TV background picture is disturbed by the settings in menu operation, a blue background can
be superimposed on the screen with »
– In a menu the individual lines or values can be selected step by step with »
Only the value that flashes in a menu on the screen can be changed.
-
+
– Change desired value with »
– Save altered settings with » OK«.
– Press » « for menu fade out without saving the altered settings.
SETTINGS
_______________________________________________________________________________
Volume setting
1
Superimpose menu on screen to change the volume with »
2
The volume level can be set between "00" and "31" with »
27
We do not recommend setting a value over "28".
3
Save volume change with » OK«.
/ OK
Note:
The menu is automatically faded out after a few seconds if the volume change is not saved with
» OK«. The set volume level is kept until the satellite TV receiver is switched to standby mode.
This volume change only influences the basic volume of the TV (via the EURO-AV socket »TV«)
and has no influence on the EURO-AV sockets »VCR« (video recorder) and »DECODER«.
Sound mute
1
Press »
« to mute sound and again to switch sound on again.
A symbol »
« appears at the top right of the screen as long as the sound is muted.
« and then taken out again.
P+
P-«.
«. Entering the value directly with »
0 ... 9
« is often possible.
-
+
« or »
«.
-
« or »
+
«.
Werbung
Inhaltsverzeichnis
