Inhaltsverzeichnis
Werbung
SETTINGS
_______________________________________________________________________________
Briefly clearing the satellite TV receiver Parental lock
1
When the satellite TV receiver is switched on from standby mode, the following appears on the
) )
. . . .
screen:
») )
. . . .
«.
2
Press the following sequence of buttons on the remote control: »
) )
– – – –
– Each full stop (.) represents a particular button. A full stop is replaced by a dash (-) after each
press of the button.
Note:
The satellite TV receiver is "unlocked" after the last correct button entry. If the satellite TV receiver
is switched to standby mode again, it is locked once again.
The lock can be cleared at any time in the »system settings« menu for a satellite TV receiver that
is switched on.
Sustained clearing of the satellite TV receiver Parental lock
1
Fade in »system settings« menu with » « and
) )
2
») )
Line
« Select.
3
Clear lock, press »
-
« or »
+
») )
X« (= Block off).
) )
X
4
Save setting with » OK«.
– The menu is faded out.
SETTINGS
______________________________________________________________________________
Overview
1
Press » « and then »2«.
?
?
300
– The status display and the menu for the channel position appear after each other.
11.494 GHZ
Settings.
$
V–A
7.02 MHZ 7.20 MHZ
~
Explanations:
PANDA
(
»
«
?
?
300
1
»
11.494
GHZ«
/
X–X
=
+
»
V–A«
$
/ OK
»
7.02 MHZ 7.20
»
~
PANDA«
»
«
(
»
1«
»
/
X–X«
»
=
+«
»
/
OK«
Channel number
The channel number is displayed as a check. It cannot be changed in the menu.
?
Satellite transmission frequency
1
The transmission frequency can be directly entered with »
-
+
1 MHz intervals with »
+
«, »
-
«, » P-«, »P+«,
»3
«.
« once.
Channel number
Satellite transmission frequency
Selection of the polarisation,
22 kHz signal on/off,
Satellite selection A/B
MHZ«
left and right audio frequency
Deemphasis/noise suppression
Recorded in the favourite table
Contrast setting
Decoder setting
Picture normal/inverted
: Exiting menu
OK: Save and leave menu
0 ...
9« or the set value changed in
«.
SETTINGS
_______________________________________________________________________________
The channel position settings menu
The satellite TV receiver is already preprogrammed for the current programmes of the Astra and
Eutelsat 13°/Hotbird satellites.
However, there are always new channels added or changes in the transmission frequencies.
The current transmission frequencies can be retrieved from video text pages from vaious stations
(e.g. SAT 1: video text page 516) or relevant journals or from the Internet pages of the satellite ope-
rator. This station can be programmed in the video menu.
Access to the image and sound settings of the individual channel positions can be gained from the
"channel position settings" menu.
1
Choose the channel position whose settings you would like to check or change with »
»
P+
P-«.
– The channel position cannot be selected with the channel number in this menu.
– The settings are withdrawn according to the description on page 26.
SETTINGS
_______________________________________________________________________________
Polarisation and switching signal
1
Select horizontal (H) or vertical (V) polarisation of the set satellite programme with
$
-
+
»
«.
Note:
For reception with several satellite aerials, several LNCs or a LNC with tone switching, the requi-
-
+
red signal source can be selected with »
(display »–«) the 22 kHz switching signal and the satellite selection »A/B«.
Detailed information can be read on pages 34 to 35, in the "Multiple satellite reception"
chapter.
Sound settings
1
Select right or left sound channel with »
P+
P-.
2
Enter sound carrier frequency directly with » 0...9« or change the set value step by step with
-
+
»
«.
Note:
16 sound settings (3 stereo, 13 mono) are preprogrammed at the factory (they cannot be
changed).
Noise suppresion
1
Choose between »PANDA«, »50 µs« (50US) and »J17« with »
~
It is up to the individual to decide on the best sound.
0 ...
9« or
« by switching on (display »~«) or switching off
-
+
«.
Werbung
Inhaltsverzeichnis
