Specifications; Standard Accessories - Hitachi CJ 120V Anleitung

English

SPECIFICATIONS

Voltage (by areas)*
Power Input*
Max. Cutting Depth
No-Load Speed
Stroke
Min. Cutting Radius
Weight (without cord)
*Be sure to check the nameplate on product as it is subject to change by areas.

STANDARD ACCESSORIES

(1) Blades (No. 41, No. 42, No. 46) ....................... 1 each
Refer to Table 1 for use of the blades.
(2) Hexagon bar wrench ................................................. 1
(3) Splinter guard ............................................................ 1
(4) Dust collecter ............................................................. 1
(5) Chip cover .................................................................. 1
(6) Shutter ........................................................................ 1
Standard accessories are subject to change without
notice.
OPTIONAL ACCESSORIES ... Sold separately
(1) Various types of blades
Refer to Table 1 for use of the blades.
(2) Guide
(3) Sub base
(4) Bench stand (Model TR12-B)
Optional accessories are subject to change without notice.
APPLICATIONS
Cutting various lumber and pocket cutting
Cutting mild steel plate, aluminum plate, and copper
plate
Cutting synthetic resins, such as phenol resin and vinyl
chloride
Cutting thin and soft construction materials
Cutting stainless steel plate (with No. 95, No. 96 or
No. 97 blade).
PRIOR TO OPPERATION
1. Power source
Ensure that the power source to be utilized conforms
to the power requirements specified on the product
nameplate.
2. Power switch
Ensure that the power switch is in the OFF position.
If the plug is connected to a receptacle while the power
switch is in the ON position, the power tool will start
operating immediately, which could cause a serious
accident.
3. Extension cord
When the work area is removed from the power
source, use an extension cord of sufficient thickness
and rated capacity. The extension cord should be kept
as short as practicable.
7
110 – 127 V
220 – 240 V
(110V, 115V, 120V, 127V, 220V, 230V, 240V)
660W
740W
Wood 120 mm
Mild Steel 10 mm
850 – 3000min
26 mm
25 mm
2.3 kg
4. Changing blades
(1) Open the lever up to the stop. (Fig. 1-I)
(2) Remove fitted blade
(3) Insert new blade up to the stop in the balde holder.
(Fig. 1-II)
(4) Close the lever. (Fig. 1-III)
CAUTION
Be sure to switch power OFF and disconnect the plug
from the receptacle when changing blades.
Do not open the lever when plunger is moving.
NOTE:
Confirm the protrusions of blade inserted to the blade
holder surely. (Fig. 2)
Confirm the blade located between the groove of
roller. (Fig. 3)
5. Adjusting the blade operating speed
This Jig Saw is equipped with the electric control
circuit which enables stepless speed control. To adjust
the speed, turn the dial shown in Fig. 4. When the dial
is set to "1", the jig saw operates at the minimum
–1
speed (850min ). When the dial set to "5", the jig saw
operates at the maximum speed (3000min
the speed according to the material to be cut and
working efficiency.
CAUTION
At low speed (dial setting: 1 or 2) do not cut a wood
with a thickness of more than 10 mm or metal with a
thickness of more than 1 mm.
6. Adjusting the orbital operation
(1) This Jig Saw employs orbital operation which moves
the blade back and forth, as well as up and down. Set
the change knob shown in Fig. 5 to "0" to eliminate
the orbital operation (the blade moves only up and
down). The orbital operation can be selected in 4 steps
from "0" to "III".
(2) For the hard material, such as a steel plate, etc.,
decrease the orbital operation. For the soft material,
such as lumber, plastic, etc., increase the orbital
operation to increase work efficiency. To cut the
material accurately, decrease the orbital operation.
7. Cutting stainless steel plates
This Jig Saw can cut stainless steel plates by using
No. 95, No. 96 or No. 97 blade. Carefully read
"Concerning cutting of stainless steel plates" for
proper operation.
8. Splinter guard
Using the splinter guard when cutting wood materials
will reduce splintering of cut surfaces.
–1
–1
). Adjust