Migatronic SIGMA SELECT BASIC Kurzanleitung Seite 11

Tabella parametri di saldatura (set value)
Processo 1,0 mm
Materiale Filo Gas S U0
(m/min) (V) (m/min)
Fe 0,8 CO 2,5 19,0 4,5
2
Fe 1,0 CO 2,0 18,0 2,5
2
Fe 1,2 CO 1,0 18,0 2,0
2
Fe 0,8 ArCO 3,0 16,0 6,0
2
Fe 1,0 ArCO 2,0 15,0 3,0
2
Fe 1,2 ArCO 1,5 16,5 2,5
2
Fe 1,6 ArCO 1,0
2
CrNi 1,0 ArCO 3,0 15,0 4,0
2
CrNi 1,2 ArCO 2,0 15,0 3,0
2
AI 1,0 Ar 4,0 14,5 6,0
AI 1,2 Ar 3,5 13,0 5,0
Processo 4,0 mm
Materiale Filo Gas S U0
(m/min) (V) (m/min)
Fe 0,8 CO 13,0 29,0 18,0
2
Fe 1,0 CO 6,0 22,5 9,0
2
Fe 1,2 CO 4,5 23,0 7,5
2
Fe 0,8 ArCO 14,0 26,0 18,0
2
Fe 1,0 ArCO 8,0 20,0 11,5
2
Fe 1,2 ArCO 5,5 20,5 8,0
2
Fe 1,6 ArCO 3,0 19,5 4,0
2
FeFlux 1,2 ArCO 6,0 21,0 8,0
2
CrNi 1,0 ArCO 9,0 25,0 10,0
2
CrNi 1,2 ArCO 8,0 24,0 10,0
2
AI 1,0 Ar 11,0 22,0 13,0
AI 1,2 Ar 10,0 18,0 13,0
Tabella 1
1,5 mm 2,0 mm 3,0 mm
S U0 S U0 S U0
(V) (m/min) (V) (m/min) (V)
19,5 7,0 21,0 11,0 27,0
19,0 3,0 200 4,5 21,0
20,0 2,5 21,0 3,5 22,0
18,0 7,5 19,5 11,0 20,0
16,0 4,0 17,0 6,0 19,0
17,5 3,5 18,0 4,5 20,5
17,0 2,0 18,0 2,5 18,5
16,0 6,0 17,0 8,5 20,0
16,0 3,5 16,5 6,0 18,0
15,0 7,5 16,0 9,0 19,0
15,0 8,0 16,0 9,0 17,0
6,0 mm 10,0 mm
S U0 S U0
(V) (m/min) (V)
30,0 24,0 37,0
24,5 14,0 32,0
28,5 11,0 36,0
31,0 24,0 33,0
26,5 16,0 30,0
29,0 10,0 32,0
22,0 5,5 29,0
25,0 11,0 28,0
27,0
24,0 12,0 31,0
25,0 15,0 27,0
23,0 15,0 26,0
GUIDA RAPIDA SIGMA SELECT BASIC
Regolazione del processo di saldatura
Tenere premuta la manopola (11A) per aprire il menù dei parametri secondari. Selezionare il
parametro girando la manopola (10) e regolarlo girando la manopola (11).
Per chiudere il menù premere brevemente (11A). Premere per breve tempo (12) per attivare la
visualizzazione di Fxx (F = function) nomi parametri on/off.
Parametri MIG/MAG
Corrente di saldatura (A)
A
m/min
t1
S S
GS.F / F22 (gas flow) 0,5-27 l/min (solo macchine con IGC) (kit opzionale)
Parametri MMA
Quando si sia impostato il programma MMA
sono selezionabili solo i seguenti parametri :
A
t
Corto circuito
Corrente di
saldatura (A)
Figura 1
Pr.G / F31 Pre-gas (0,2 sec.)
S.St / F32 Soft start (1,0 m/min.)
Po.G / F38 Post-gas (3,0 sec.)
SP.t / F39 Tempo puntatura/Spot time (0,0 sec.)
t2
S
t
HS.A / F11 Hotstart (25%)
HS.t / F12 Tempo di Hotstart (0,5 sec.)
Arc / F13 Arc power (25%)
t
IT
50113805