Mebus 10380 Bedienungsanleitung Seite 14

A SNOOZE Key
Activate the snooze function
B AL. 1 Key
Display the alarm time or sets the alarm status for
alarm 1
C AL. 2 Key
Display the alarm time or sets the alarm status for
alarm 2
D ( ) Key
Decrease the Value of a setting
E ( ) Key
Increase the Value of a setting; Force to receive
Radio-controlled Clock signal
F SEARCH key
Force to search for remote sensor signal
G MEM key
Receive the maximum or minimum temperature
and humidity of main unit and remote unit
H CHANNEL key
Toggle among different channels of the remote
sensor units. Key sequence: Indoor > Channel 1
> Channel 2 > Channel 3 > Indoor... Also, you can
press and hold to enter the Auto Scroll function
I MODE Key
Toggles the display modes and confirms entry
while setting the values for display
J RESET key
Press to reset all values to their default setting
59
BEFORE YOU BEGIN
For best operation,
1. Insert batteries for remote units before doing so for
the main unit.
2. Position the remote unit and main unit within effective
transmission range, which, in usual circumstances, is
20 to 30 meters. Note that the effective range is vastly
affected by the building materials and where the main
and remote units are positioned. Try various set-ups
for best result. Though the remote units are weather
proof, they should be placed away from direct
sunlight, rain or snow.
BATTERY INSTALLATION: REMOTE UNIT
1. Remove the screws on the battery compartment.
2. Select the channel
3. Install 2 batteries (UM-3 or "AA" size 1.5V) strictly
according to the polarities shown.
4. Replace the battery compartment door and secure
its screws.
TURN ON MAIN UNIT
To install 2 batteries (UM-3 or AA size 1.5V) strictly into
the main unit and plug the AC-adaptor to give power to
the main unit as well, you will see the display is lighted up.
LOW BATTERY WARNING
FOR THE REMOTE SENSOR
When it is time to replace batteries for the remote sensor,
the respective low battery indicator
display. In addition, the low battery indicator
show up on the Main Unit display for this specified
Remote Sensor Unit.
61
MAIN FEATURES: REMOTE UNIT
A LED INDICATOR
Flashes once when the remote unit transmits a reading
Flashes twice when low battery is detected on
sensor unit
B BATTERY COMPARTMENT
Accommodates two AA-size batteries
C RESET BUTTON
Press to reset all setting if you have selected
different channel.
D CHANNEL SELECTOR
Select the channel before you install batteries.
E WALL-MOUNT RECESSED HOLE
Supports the remote until in wall-mounting
F ˚C/ ˚F BUTTON
FOR THE MAIN UNIT
When the battery power is not enough, there is a
battery icon
need to use the new batteries.
If the AC-adaptor cannot connect to the Main Unit
properly, or the AC-adaptor is removed out of the
Main Unit, the icon
SETTING UP THE REMOTE
TEMP. AND RC CLOCK
a. Once batteries are in place for the remote unit, they
will start transmitting temperature and humidity
readings at around 45 seconds intervals.
The main unit will also start searching for signals for
about two minutes once batteries are installed. 10
seconds upon successful reception, the outdoors
temperatures and humidity will be displayed .The
main unit will automatically update its readings at
about 45-second intervals.
b. If no signals are received, blanks "
displayed.
Hold [ SEARCH ] for 2 seconds to enforce another
search for about 2 minutes. This is useful in
synchronizing the transmission and reception of the
remote and main units.
c. When remote signal reception is finished, it will
automatically synchronize its current time and dated
when brought within rang of the "DCF" RF signal.
Repeat this step whenever you find discrepancies
will show up on
between the reading shown on the main unit and that
will
on the remote unit.
WIRELESS THERMO • HYGRO
A C
RESET
1 2 3
CHANNEL
60
will be shown on the display, so we
will be shown on display.
" will be
62
E
F
D
B