TRM-202 MK3 ROTARY MIXER Der TRM-202 MK3 von Omnitronic bietet dem DJ mit seinen klassischen ALPS-Drehreglern (Blue Velvet RK27) eingebauten 3-Band-Frequenzisolator die typischen Features eines Rotary-Mixers. Durch die hochwertigen Bauteile ist ein gutes und ansprechendes Klangbild gegeben. Die großen Drehregler beider Kanäle erlauben sehr sanfte Übergänge, welche mit einem herkömmlichen...
Inhalt 1 Einführung 1 Einführung ..........3 Willkommen bei Omnitronic! Schön, dass Sie sich für eines unserer Produkte entschieden haben. 2 Sicherheitshinweise ......... 4 3 Bestimmungsgemäße Verwendung ..5 Diese Bedienungsanleitung zeigt Ihnen, wie Sie 4 Bedienelemente und Anschlüsse ... 6 das Mischpult installieren und nutzen.
• Die Kabeleinführung oder die Kupplung am 2 2 2 2 Sicherheitshinweise Gerät dürfen nicht durch Zug belastet werden. Es muss stets eine ausreichende Kabellänge zum Gerät hin vorhanden sein. Andernfalls kann Achtung! das Kabel beschädigt werden, was zu tödlichen Stromschlägen führen kann.
3 3 3 3 Bestimmungsgemäße • Das Gerät darf nicht in einer Umgebung eingesetzt oder gelagert werden, in der mit Verwendung Spritzwasser, Regen, Feuchtigkeit oder Nebel zu rechnen ist. Feuchtigkeit oder sehr hohe Das Gerät dient zum kreativen Mixen von Line- Luftfeuchtigkeit kann die Isolation reduzieren und Phono-Signalquellen und wurde speziell für und zu tödlichen Stromschlägen führen.
Seite 7
Funktion Regler BASS zum Anheben und zum Auslöschen von Frequenzen im Tiefenbereich (z. B. für Acapella-Effekte) Regler MID zum Anheben und zum Auslöschen von Frequenzen im Mittenbereich (z. B. zum Unterdrücken von Gesang und Melodie des Tonmaterials) Regler HIGH zum Anheben und zum Auslöschen von Frequenzen im Höhenbereich (z.
Seite 8
Netzschalter Netzanschluss Sicherungshalter. Ersetzen Sicherung ausgestecktem Gerät und nur durch eine gleichwertige Sicherung. Der korrekte Wert ist am Gerät angegeben. Erdungsklemme für angeschlossene Plattenspieler Regler PH SENS zum Anpassen der Eingangsverstärkung von Phono-Eingang 2 an Line-Pegelquellen Schaltet die Buchsen PH 2/LINE 3 für Kanal 2 zwischen Phono- und Line-Eingang um. Stereo-Eingänge (Cinch) für Kanal 2 zum Anschluss von Geräten mit Line-Pegel wie CD-Player (LINE 3, 4) oder Plattenspielern mit Magnettonabnehmersystem (PH 2) Symmetrischer XLR-Ausgang L/R zum Anschluss an Verstärker bzw.
5 5 5 5 Inbetriebnahme Verkabelung Das Mischpult bietet eine Vielzahl von Möglichkeiten für den symmetrischen oder unsymmetrischen Anschluss professioneller Audiogeräte. Um Störgeräusche zu vermeiden, sollte das Pult vor dem Herstellen und Trennen von Verbindungen ausgeschaltet sein oder die Kanal- und Ausgangsregler auf Minimum gestellt werden.
Due to its booth output and a separate volume control, the TRM-202 MK3 is a perfect fit for clubs. Thanks to the record output, DJs can easily record their sets.
1 Introduction Contents Welcome to Omnitronic! Thank you for choosing 1 Introduction ..........12 one of our products. 2 Safety Instructions ......... 13 3 Operating Determinations ..... 14 This user manual will show you how to install and 4 Operating Elements and Connections . 15 operate the mixing console.
• If extension cords are used, make sure that the 2 2 2 2 Safety Instructions core diameter is sufficient for the required power consumption device. warnings concerning the power cords are also valid for Caution! possible extension cords. • Always disconnect from the mains, when the Keep this device away from rain and moisture! device is not in use or before cleaning it.
3 3 3 3 Operating Serial Barcode • Never remove the serial barcode from the Determinations device as this would make the guarantee void. Transport This device is used to mix line and phone signal • Please use the original packaging if the device sources.
4 4 4 4 Operating Elements and Connections 15 • EN...
Seite 16
Function Control BASS boosts and cuts frequencies in the bass range (e.g. for acapella effects) Control MID boosts and cuts frequencies in the middle range (e.g. to cut vocals and melody from the source material) Control HIGH boosts and cuts frequencies in the high range (e.g. to emphasize the sound of the cymbals or hi-hats) Input source selector switch for channel 1 (phono 1/line 1 or line 2) Control HIGH adjusts the high range for channel 1...
Seite 17
Power on/off Power input with fuse holder. Used to plug in the supplied power cable. Only replace the fuse when the device is disconnected from mains. Only use fuses of the same rating and power. The correct fuse value is specified on the rear panel. Ground clamping screw for turntables Gain control for matching the input amplification of phono input 2 to line level sources Switches the PH 2/LINE 3 jacks for channel 2 between phono and line input...
5 5 5 5 Setup Cable connections The console offers numerous, highly flexible possibilities for balanced or unbalanced connection of professional audio equipment. To avoid interfering noise, switch off the mixer or set the channel volume control and output controls to minimum prior to connecting and disconnecting equipment. Be sure to use only high-grade cables.
6 6 6 6 Technical Specifications TRM-202 MK3 Power supply: 100-240 V AC, 50/60 Hz Power consumption: 20 W Gain: Line: 20 dB Phono: 60-75 dB Mic: 44 dB Max. output level: 22 dBu Frequency range: Line: 20-20000 Hz Phono:...