Inhaltsverzeichnis
Werbung
Manual of Sensorless Brushless Motor Speed Controller
Normal startup procedure:
Move throttle
Connect battery
stick to
special tone like
bottom and
then switch
power supply is OK
on transmitter.
Throttle range setting: (Throttle range should be reset whenever a new transmitter is being used)
Switch on
Connect battery
transmitter,
pack to ESC,
move throttle
and wait for
stick to top
about 2 seconds
Program the ESC with your transmitter (4 Steps):
1.
Enter program mode
2.
Select programmable items
3.
Set item's value (Programmable value)
4.
Exit program mode
1. Enter program mode
1)
Switch on transmitter, move throttle stick to
top , connect the battery pack to ESC
2)
Wait for 2 seconds, the motor should emit
special tone like "beep-beep-"
3)
Wait for another 5 seconds, special tone like
"
" should be emitted, which means
program mode is entered
3. Set item value (Programmable value):
You will hear several tones in loop. Set the value matching to a tone by moving throttle stick
to top when you hear the tone, then a special tone "
and saved. (Keeping the throttle stick at top, you will go back to step 2 and you can select
other items; Moving the stick to bottom within 2 seconds will exit program mode directly)
Tones
Items
1 short tone
Brake
Battery type
Li-ion / Li-poly
Cutoff mode
Cutoff threshold
Start mode
Timing
Best.-Nr. / Item-No. / art. 018-1100
Several "beep-" tones
pack to ESC,
should be emitted,
presenting the number
" 123" means
of lithium battery cells
"Beep-Beep-" tone
should be emitted,
means throttle range
highest point has been
correctly confirmed
"beep-"
"beep-beep-"
2 short tones
Off
On
NiMH / NiCd
Soft-Cut
Cut-Off
Low
Medium
Normal
Soft
Low
Medium
When self-test is
finished, a long
"beep-----"tone
should be emitted
Move throttle stick to the
bottom, several "beep-" tones
should be emitted, presenting
the number of battery cells
2. Select programmable items:
After entering program mode, you will hear 8 tones in a loop with
the following sequence. If you move the throttle stick to bottom
within 3 seconds after one kind of tones, this item will be selected.
1.
"beep"
2.
"beep-beep-"
3.
"beep-beep-beep-"
4.
"beep-beep-beep-beep-" cutoff threshold
5.
"beep-----"
6.
"beep-----beep-"
7.
"beep-----beep-beep-"
8.
"beep-----beep-----"
Note: 1 long "beep-----" = 5 short "beep-"
" emits, means the value is set
"beep-beep-beep"
3 short tones
High
Super soft
High
Ver HW-01-081027.1
Move throttle stick
upwards to go flying
A long "Beep-" tone should
be emitted, means throttle
range lowest point has
been correctly confirmed
brake
(1 short tone)
battery type
(2 short tone)
cutoff mode
(3 short tone)
(4 short tone)
startup mode
(1 long tone)
timing
(1 long 1 short)
set all to default (1 long 2 short)
e x i t
( 2 l o n g t o n e )
4. Exit program mode
There are 2 ways to exit
program mode:
1.
In step 3, after special
tone "
", please
move throttle stick to
the bottom position
within 2 seconds.
2.
In step 2, after tone
"beep-----beep-----"(ie.
The item #8), move
throttle stick to bottom
within 3 seconds.
- 4 -
Seite 9
Werbung
Inhaltsverzeichnis
