Technical Data; Noise/Vibration Information; Battery Charging - Bosch GHO 12V-20 Professional Originalbetriebsanleitung

OBJ_BUCH-2967-001.book Page 14 Tuesday, June 6, 2017 10:34 AM
14 | English
7 Drawer for spare blades
8 Lateral blade-shaft protector
9 Planer base plate
10 Battery charge-control indicator
11 Screw for belt cover
12 Belt cover
13 Chip ejector (can be inserted on the right-hand or left-
hand side)
14 Adjustable planer base plate
15 V-groove
16 Handle (insulated gripping surface)
17 Carbide blade (TC)
18 Hex key
19 Blade drum
20 Clamping element for blade
21 Fastening screw for planer blade (2x)
22 Dust extraction hose (Ø 35 mm)(Click & Clean)*
23 Chip/dust bag*
24 Extraction adapter (Click & Clean)*
25 Locking device*
26 Snap-fastener
*Accessories shown or described are not part of the standard de-
livery scope of the product. A complete overview of accessories
can be found in our accessories program.

Technical Data

Planer
Article number
Rated voltage
No-load speed
Planing depth
– optimum
– maximum
Rebating depth
Planing width, max.
Weight according to EPTA-
Procedure 01:2014
Permitted ambient
temperature
– during charging
**
– during operation and
during storage
Recommended batteries
Recommended chargers
* depending on the battery pack being used
** limited performance at temperatures <0 °C
Under seldom circumstances, the tool may stop running in case of elec-
trostatic discharge. After repressing the On/Off switch the tool works as
intended to use.
1 609 92A 24V | (6.6.17)

Noise/Vibration Information

Sound emission values determined according to
EN 60745-2-14.
Typically the A-weighted sound pressure level of the product
is 79 dB(A). Uncertainty K=3 dB.
The noise level when working can exceed 80 dB(A).
Wear hearing protection!
Vibration total values a
determined according to EN 60745-2-14:
a
h
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with anoth-
er. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or insertion tools or is
poorly maintained, the vibration emission may differ. This
may significantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working
period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
terns.
GHO 12V-20
3 601 EA7 0..
Assembly
V= 12
 Before any work on the machine itself (e. g. mainte-
-1
min 14500
mm 0 – 1.0
mm 1.0 – 2.0
mm 0 – 17

Battery Charging

mm 56
 Use only the battery chargers listed on the accessories
kg 1.7 – 1.9*
Note: The battery supplied is partially charged. To ensure full
capacity of the battery, completely charge the battery in the
°C 0...+45
battery charger before using your power tool for the first time.
The lithium-ion battery can be charged at any time without re-
°C –20...+50
ducing its service life. Interrupting the charging procedure
GBA 12V ...
does not damage the battery.
GBA 10,8V...
The lithium-ion battery is protected against deep discharging
GAL 12..
by the "Electronic Cell Protection (ECP)". When the battery is
GAL 18..W
empty, the machine is switched off by means of a protective
circuit: The inserted tool no longer rotates.
AL 11..
 Do not continue to press the On/Off switch after the
(triax vector sum) and uncertainty K
h
2 2
<2.5 m/s , K=1.5 m/s .
nance, tool change, etc.) as well as during transport
and storage, remove the battery from the power tool.
There is danger of injury when unintentionally actuating
the On/Off switch.
page. Only these battery chargers are matched to the lith-
ium-ion battery of your power tool.
machine has been automatically switched off. The bat-
tery can be damaged.
Bosch Power Tools