Product Description And Specifications; Intended Use; Product Features; Technical Data - Bosch 3 603 BA4 0 Originalbetriebsanleitung

Use clamps or another practical way to secure and
u
support the workpiece to a stable platform. Holding
the workpiece by your hand or against the body leaves it
unstable and may lead to loss of control.
Only bring the power tool into contact with the work-
u
piece when switched on. Otherwise there is danger of
kickback if the cutting tool jams in the workpiece.
Do not allow the chip ejector to come into contact with
u
your hands. You may be injured by rotating parts.
Never plane over metal objects, nails or screws. Cut-
u
ters and cutter shafts could become damaged and cause
increased vibration.
Use suitable detectors to determine if utility lines are
u
hidden in the work area or call the local utility com-
pany for assistance. Contact with electric lines can lead
to fire and electric shock. Damaging a gas line can lead to
explosion. Penetrating a water line causes property dam-
age or may cause an electric shock.
While working, always hold the planer in such a way
u
that the planer base plate lies flat against the work-
piece. Otherwise the planer could slip and cause injury.
Products sold in GB only:
Your product is fitted with an BS 1363/A approved electric
plug with internal fuse (ASTA approved to BS 1362).
If the plug is not suitable for your socket outlets, it should be
cut off and an appropriate plug fitted in its place by an au-
thorised customer service agent. The replacement plug
should have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains
socket elsewhere.
Hold the power tool firmly with both hands and make
u
sure you have a stable footing. The power tool can be
more securely guided with both hands.
Product Description and
Specifications
Read all the safety and general instructions.
Failure to observe the safety and general in-
structions may result in electric shock, fire
and/or serious injury.
Please observe the illustrations at the beginning of this oper-
ating manual.

Technical Data

Planer
Article number
Rated power input
Power output
No-load speed
Cutting depth
Rebate depth
Bosch Power Tools

Intended use

The power tool is intended for planing wood-based materials
such as beams and boards while resting firmly on the work-
piece. It is also suitable for chamfering edges and for rebat-
ing.

Product features

The numbering of the product features refers to the diagram
of the power tool on the graphics page.
(1) Chip ejector (PHO 2000: either right or left)
(2) Knob for setting the cutting depth (insulated gripping
surface)
(3) Cutting depth scale
(4) Changeover lever for chip ejector direction (PHO
2000)
(5) Lock-off switch for on/off switch
(6) On/off switch
(7) Storage compartment
(8) V-grooves
(9) Planer base plate
(10) Handle (insulated gripping surface)
(11) Blade head
(12) Clamping element for planer blade
(13) Fastening screw for planer blade
(14) HM/TC planer blade
(15) Hex key
(16) Vacuum hose (dia. 35 mm)
A)
(17) Dust/chip bag
A)
(18) Parallel guide
(19) Scale for rebate width
(20) Locking nut for rebate width setting
(21) Fastening screw for parallel/angle guide
A)
(22) Angle guide
(23) Locking nut for angle setting
(24) Fastening screw for rebate depth guide
A)
(25) Rebate depth guide
(26) Parking rest
A) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.
PHO 1500
3 603 BA4 0..
W
W
-1
min 19 500
mm 0–1.5
mm
English | 13
A)
A)
A)
A)
A)
A)
PHO 2000
3 603 BA4 1..
550
280
19 500
0–2.0
0–8
1 609 92A 49E | (12.11.2018)
680
400
0–8