Optional Accessories - Makita VC3211H Betriebsanleitung

• A technical inspection, including inspection of filters, air
tightness, and control mechanism, must be performed
by an instructed person at least once a year, or more
frequently as may be specified by national
requirements.
• During maintenance, all contaminated items which
cannot be satisfactorily cleaned must be disposed.
Such items must be disposed of in impervious bags
which accord with your country's regulations.
• After the operation in the hazardous area, the outside
of the tool must be decontaminated by vacuum
cleaning methods and wiped clean or treated with
sealant before you take the tool out of a hazardous
area. All the parts of the tool must be regarded as
contaminated when removed from the hazardous area,
and appropriate action must be taken to prevent dust
dispersal.
• Change the air filter when the air filter is clogged with
dust or you feel that the cleaner's performance
declined.
• Check the filters periodically. If there is a tear on it,
replace it immediately.
Removing the air filter
CAUTION:
• Wait for about 5 minutes so that dust in the tank
completely settles down.
• Make sure that the tool is unplugged.
• Be careful not to let the dust enter inside the tank cover
when removing the air filter.
Unhook the tank cover and remove it carefully. Put it up
side down. (Fig. 15)
Remove the screw on the stopper lever.
Unlock the filter hooks by flipping the stopper lever.
(Fig. 16)
Cover the air filters with a plastic bag. (Fig. 17)
Remove the air filters from the tank cover carefully and tie
the plastic bag firmly. (Fig. 18)
Assembling the air filter
When you get the air filter components separately,
assemble them as follows.
Put the prefilter over the powder filter. (Fig. 19)
Make sure that the borders of prefilter and powder filter
are set properly. (Fig. 20)
Installing the air filter (Fig. 21)
Wipe off the seal face.
Set the new air filters and fix them with the filter hooks.
Make sure that the air filters are set at the correct position.
Flip the stopper lever to lock the air filters.
Lock the filter hooks with the screws.
Set the tank cover onto the tank and lock it with hooks.
Cleaning the level sensors (Fig. 22)
The level sensors detect liquid when the tank becomes
full with liquid. Clean the level sensors with a soft cloth
from time to time when changing the air filters.
10
Storage of power supply cord (Fig. 23 &
24)
Wind up the power supply cord around the multi-hook or
the base hook.
Storage of accessories
NOTE:
• Do not apply an excessive force to the accessories that
are held by the pipe holder. Applying an excessive
force to these accessories may cause damage to the
pipe holder.
Pipe rest can be used to store straight pipe, bent pipe and
others by just inserting these accessories. (Fig. 25)
The pipes can be placed into the pipe holder when also
stopping using the cleaner on the way for a while.
(Fig. 26)
You can place the cap in multi-hook while the hose is
connected to the tool. (Fig. 27)
Storage of hose (Fig. 28 & 7)
The hose can be placed on either base hook or multi-
hook.
To maintain product SAFETY and RELIABILITY, repairs,
any other maintenance or adjustment should be
performed by Makita Authorized Service Centers, always
using Makita replacement parts.

OPTIONAL ACCESSORIES

CAUTION:
• These accessories or attachments are recommended
for use with your Makita tool specified in this manual.
The use of any other accessories or attachments might
present a risk of injury to persons. Only use accessory
or attachment for its stated purpose.
If you need any assistance for more details regarding
these accessories, ask your local Makita Service Center.
• Hose
• Front cuffs (22, 24, 38)
• Straight pipe
• Corner nozzle
• Round brush
• Powder filter
• Damper
• Prefilter
• Nozzle assembly
• Bent pipe
• Filter bag
• Hose band
• Belt hook complete
• Cap
NOTE:
• Some items in the list may be included in the tool
package as standard accessories. They may differ
from country to country.