Starting And Stopping - Husqvarna Automower 310 Kurzanleitung

1. PL ACEMENT OF AND CONNECTING THE CHARGING STATION
See chapters 3.2 and 3.3 in the Operator's Manual
1. Place the charging station at a central position in the working area, with a lot of open space in front of the charging station
and on a relatively horizontal surface.
2. Connectthepowersupply'slowvoltagecabletothechargingstationandthepowersupply.
3. Connectthepowersupplytoa100-240Vwallsocket.
4. Place the robotic lawnmower in the charging station to charge the battery while the boundary wire is laid. Set the main
switch to position 1.
2. PL ACEMENT OF THE BOUNDARY WIRE AND THE GUIDE WIRE
See chapter 3.4 in the Operator's Manual
1. Lay the boundary wire so that it forms a loop around the working area.
2. Make an eyelet at the point where the guide wire will later be connected.
3.  R untheguidewiretothepointontheboundaryloopwheretheconnectionwillbemade.Avoidlayingthewireattight
angles.
3. CONNECTING THE BOUNDARY WIRE AND THE GUIDE WIRE
See chapter 3.5 in the Operator's Manual
1.  N arrowpassagesinthegardenmakeitdifficultfortheroboticlawnmowertofindthechargingstation.Therobotic
lawnmowercanbeleadtoremotegardenareasusingtheguidewire.Theguidewirealsohelpstheroboticlawnmowerto
quicklyfindthechargingstation.
2.  L aytheguidewireunderthechargingstationandatleast2metres=meters(US)straightoutfromthefrontedgeofthe
charging station.
3. Open the connectors and lay the wire ends in the recesses on each connector.
4. Press the connectors together using a pair of pliers.
5. Cutoffanysurplusboundarywire.Cut1to2cmabovetheconnectors.
6.  P resstheconnectorsontothecontactpins,markedAL(left)andAR(right),onthechargingstation.Itisimportantthatthe
right-handwireisconnectedtotheright-handcontactpin,andtheleft-handwiretotheleft-handpin.
7. Fasten the connector to the contact pin marked G1 on the charging station.
4. CONNECTING THE GUIDE WIRE TO THE BOUNDARY WIRE
See chapter 3.6 in the Operator's Manual
1. Cuttheboundarywirewithawirecuttersatthecentreoftheeyeletthatwasmadeinstep2.2.
2.  C onnecttheguidewiretotheboundarywireusingtheaccompanyingcouplers.Pressthecouplerscompletelytogether
with a polygrip.

5. STARTING AND STOPPING

See chapters 4.4 and 4.5 in the Operator's Manual
STARTING
1. Open the cover by pressing the STOP button.
2. Set the main switch to position 1.Whenyoudothisforthefirsttime,astartupsequencestartswhereyouselectafour
digitPINcodeamongotherthings.
3. Press the START button and close the cover.
STOPPING
Press the STOP button.
6. ADJUSTING THE ROBOTIC L AWNMOWER TO SUIT THE SIZE OF YOUR L AWN
See chapter 6.3 in the Operator's Manual
Themowingresultsdependonmowingtime.AdjustthemowingtimetosuityourgardenusingtheTimer function. You
decide what times during the day the robotic lawnmower is to work. Theroboticlawnmowermowsabout68m
day(56m forAutomower®310).Forexample;Iftheworkingareais800m
2
12hoursperday(about15hoursforAutomower®310).
7. MAINTENANCE
See chapter 8 in the Operator's Manual
1.  T hemainswitchshouldbeinthe0 position during all work on the robotic lawnmower's chassis, such as cleaning or
replacing the blades.
2.  N everuseahigh-pressurewasherorevenrunningwatertocleantheroboticlawnmower.Neverusesolventsforcleaning.
Replacethebladesregularlyforthebestmowingresult.
3. Allconnectionstothechargingstation(powersupply,boundaryandguidewire)mustbedisconnectedifthereisariskofa
thunderstorm.
4. Fully charge the battery at the end of the season before winter storage.
QG,1157865,310-315,2016_151127.indd 6
the robotic lawnmower must operate for about
2
EN
per hour and
2
2015-11-27 11:45:50