Operation - Scheppach Dp55 Original Bedienungsanleitung

3. Tighten the blade fastening screw (B) firmly.
8.5 Assembling the clamping lever for depth stop
(fig. 2)
Assemble the clamping lever for depth stop (6) as
shown in fig. 2.
8.6 Fastening to a work surface (fig. 3)
Fasten the device to the work surface by bolting the
base plate (1) to the work surface.
9.

Operation

9.1 Operation of the display (fig. 4)
• Switching the display on/off:
Press the button (I, 2-3 sec.) until the display (9) switch-
es on or off.
• Adjusting the oscillation rate
• Press the button to increase the oscillation rate
(fig. 12.1).
• Press the button to decrease the oscillation rate
(fig. 12.2).
• Switching the laser cross on/off:
The laser cross can be switched on or off by pressing
the button (12.3).
9.2 Height adjustment (fig. 1)
The position of the machine head can be adjusted to
suit the workpiece height or the workpiece length.
1. Hold the handle (8) firmly.
2. Release the clamping lever for the height adjust-
ment (5).
3. Set the position of the machine head with the han-
dle (8).
4. Secure the position of the machine head with the
height adjustment clamping lever (5).
Attention! Ensure in the lowest machine head position
that the machine head will not be moved beyond the
marking.
Use the clamping lever for height adjustment (5) to se-
cure the machine head in this position. Otherwise, the
guide could be damaged.
9.3 Setting the drilling depth (fig. 1, 11)
The drilling depth can be set with the depth stop (7).
1. Release the clamping lever on the depth stop (6).
2. Carry out a test drilling.
As soon as the desired depth, tighten the depth
stop clamping lever (6) again.
3. The depth stop (7) is now locked in the desired
drilling depth.
4. Then check the position of the depth stop. If
necessary, loosen the pointer (18) with a Phillips
screwdriver, set the scale (20) to 0° position and
re-tighten the retaining screw (19).
9.4 Clamping/releasing drill bits (fig. 4, 7)
Caution! Always release the chuck key. Risk of in-
jury due to chuck key being thrown away!
9.4.1 Clamping
1. Fold the tension chuck guard (13) upwards.
2. Insert the chuck key (G).
3. Turn the chuck key (G) counterclockwise, to open
the clamping sleeve (E).
4. Insert the insertion tool (F).
5. Hold the insertion tool (F) firmly.
6. Turn the chuck key (G) clockwise, to close the
clamping sleeve (E) and to secure the insertion tool.
7. Check that the insertion tool (F) is tightly fitted.
8. Pull the chuck key (G) apart.
9.4.2 Releasing:
1. Fold the tension chuck guard (13) upwards.
2. Insert the chuck key (G).
3. Turn the clamping sleeve (G) clockwise until the
installation tool (F) can be removed.
4. Pull the chuck key (G) apart.
9.5 Aligning workpieces
1. Switch on the laser cross via on/off switch (12.3).
2. The intersection of the two laser lines exactly indi-
cates the centre point of the drill.
3. Align your marking on the workpiece with the laser
cross.
9.6 Clamping the workpiece (fig. 6)
It must be possible to clamp the workpiece securely.
Do not work with workpieces that cannot be clamped
securely.
The cut-out of the quick clamp must be centrally
aligned with the hole to be drilled. Otherwise, the drill
bit or the chuck could be obstructed by the quick clamp.
1. Position the workpiece with the help of the laser
cross.
2. Loosen the quick clamping lever (17).
3. Place the quick clamp (2) on the workpiece.
4. Turn the quick clamp lever (17) clockwise to clamp
the workpiece.
www.scheppach.com GB | 29