Herunterladen Inhalt Inhalt Diese Seite drucken

JVC KS-FX430R Bedienungsanleitung Seite 14

Inhaltsverzeichnis

Werbung

Verfügbare Sprachen

Verfügbare Sprachen

Other RDS functions
EON (Enhanced Other Networks)
• When tuning in a broadcasting station
transmitting EON data, the EON indicator
is lit and the following operations start.
EON automatically stores the frequencies
of stations from other networks transmitting
information codes (TP/TA/AF/PTY/PS
(Programme Service), etc.) so they can be
mutually used. The following points have
been improved:
When listening to a station NOT transmitting
traffic information or the selected PTY for
example, EON automatically tunes to a station
in a local network when this information is
broadcast and then switches back to the
original programme when the broadcast ends.
(However, it does not switch back to the
original programme if the broadcast continues
for a long time.) The transmitted information
(AF and other codes) is constantly and
automatically updated so that preset
programme information can be heard
immediately even if in a different network area.
Traffic information volume control
This function adjusts the volume of traffic
information broadcasts.
1. Press the SEL button for more than 2
seconds to set the preferred setting mode.
2. Select "TA VOL" with the
3. Set to the desired volume with the + or –
button. (See page 22.)
Number buttons
When a number button is pressed, if the
station with that frequency is broadcasting a
sufficiently strong signal, the receiver will tune
to that frequency.
When the signal strength is not sufficient for
good reception, by referring to the AF list, the
receiver searches for a station broadcasting
the same programme with a stronger signal.
If a station cannot be found in the AF list, PI-
seek tuning starts. If a station broadcasting
the same PI code cannot be detected in one
search-cycle, PI-seek tuning is released and
the original preset frequency is tuned to.
CT (Clock Time)
When CT data is received in the RDS signal,
the time is correctly renewed.
• RDS updates the local time according to
Greenwich Mean Time.
14
• When automatic renewal of clock time is
NOT required, follow the steps below.
1. Press the SEL button for more than 2
seconds to set the preferred setting mode.
2. Select "AUTO ADJ" with the
button.
3. Press the – button and set to "ADJ OFF".
(See page 22.)
Once these steps are completed, clock time
is not renewed even if the CT (Clock Time)
data is received with the RDS signal. When
you wish to reactivate this mode, repeat the
same procedure and in step 3 press the +
button to set to "ADJ ON." In the activated
mode, clock time is automatically renewed
when the CT data is received.
Note:
It takes at least 2 minutes to renew the time after
receiving CT data. The station must be received
for more than 2 minutes continuously, otherwise
the clock time will NOT be renewed.
Display Mode
Setting the main display mode.
1. Press the SEL button for more than 2
seconds to set the preferred setting mode.
2. Select "DISPMODE" with the
button.
3. Select the desired mode with the + or –
button.
or
button.
(Station name (PS NAME) Ô Frequency
being received (FREQ) Ô Clock time
(CLOCK) Ô) (See page 22.)
Note:
When the "CLOCK" mode is set, clock time
remains on the main display even during tape (or
CD (KS-FX430R only)) playback.
Display Button
The DISP button is used to select the
Operation (Tuner, Tape or CD (KS-FX430R
only)) and Clock modes. Each time the button
is pressed, the display changes as follows:
Operation mode (Station name* = Frequency
being received = PTY* ; or TAPE; or CD (KS-
FX430R only)) = Clock time.
The display returns to the initially preset mode
after a short while.
* When the RDS or PTY signal is weak or
when not tuned to an RDS or PTY station,
the Station name or PTY is NOT displayed.
or
or

Werbung

Inhaltsverzeichnis

Fehlerbehebung

loading

Diese Anleitung auch für:

Ks-fx330r

Inhaltsverzeichnis