Custom Code Setting; Switching The Upper Limit Of Cooling Temperature; Dip Switch Setting; Function Setting - AirStage 9367702107 Installationsanleitung

(3) Remote controller address
i) 3-wire type
Rotary switch (RC AD SW)...Factory setting "0"
When connecting multiple indoor units to 1 standard wired remote controller, set the
address at RC AD SW in sequence from 0.
Setting Setting range
Remote controller
0 to 15
address
Example
If 4 indoor units are connected.
Indoor unit Indoor unit
RC AD SW RC AD SW
0 1
Remote
controller
RC AD SW 0 1
Address 0 1
RC AD SW 8 9
Address 8 9
ii) 2-wire type
Rotary switch (RC AD SW)...Factory setting "0"
Since the remote controller address settings are automatically confi gured, you do not
need to confi gure them.
If confi guring manually, it is necessary to confi gure both the indoor unit and the remote
controller.
For details, please refer to the remote controller manual.
] 1

7.2. Custom code setting

Selecting the custom code prevents the indoor unit mix-up. (Fig. B)
(Up to 4 codes can be set.)
Perform the setting for both the indoor unit and the remote controller.
Fig. B
Confusion
Indoor unit
Remote
controller
Custom code setting for indoor unit
Set the DIP switch SET 3 SW1, SW2, referring to the Table B.
ON
OFF
SW SW SW SW
1 2 3
A (Factory setting)
DIP switch SET 3 SW1 OFF
DIP switch SET 3 SW2 OFF
En-13
9367702107-01_IM.indb Sec1:13 9367702107-01_IM.indb Sec1:13
Type of switch
Setting
example
0
RC AD
Indoor unit Indoor unit
RC AD SW RC AD SW
2 3
2 3 4 5 6 7
2 3 4 5 6 7
A B C D E F
10 11 12 13 14 15
Code change
A B C D
A B C D
DIP switch
"SET 3"
4
Table B
Custom code
B C
ON OFF ON
OFF ON ON

7.3. Switching the upper limit of cooling temperature

This setting can be raised the upper limit of the cooling temperature setting range.
This setting can be used when connecting to the following controllers.
• Wired remote controller (2-wire type)
• Central remote controller
• Touch panel controller
• System controller
• Service tool
• Web monitoring tool

DIP switch setting

Set the DIP switch SET 4 SW3 referring to the Table C.
ON
OFF
DIP switch SET 4 SW3
OFF (Factory setting)
ON
NOTE :
Please do not make a standard setup and an extension setup intermingled in remote
controller group.
1 FUNCTION SETTI

7.4. Function setting

• FUNCTION SETTING can be performed with the wired or wireless remote controller.
(The remote controller is optional equipment)
• Refer to the wired or wireless remote controller manual for detailed setting information.
(Set IU AD, REF AD SW to 0)
• Refer to "7.1. Setting the address" for indoor unit address and refrigerant circuit address
settings.
• Turn the power of the indoor unit ON before starting the setting.
* Turning on the power to the indoor units initializes EEV, so make sure the piping air
tight test and vacuuming have been conducted before turning on the power.
* Also check again to make sure no wiring mistakes were made before turning on the
power.
Function details
Function
Function Setting number
number
00
Filter
indicator 11
01
interval
02
00
Filter
01
indicator 13
action
Display only on
02 central remote
00
Horizontal
swing
24
01
airfl ow
direction
02
D
00
Cool air
tem-
30
01
perature
trigger
02
DIP switch "SET4"
SW SW SW SW
1 2 3 4
Table C
Cooling temperature setting range
Standard (18 to 30 °C)
Extension (18 to 32 °C)
Default Details
○
Default Adjust the fi lter cleaning interval
notifi cation. If the notifi cation is too
early, change to setting 01. If the
Longer
notifi cation is too late, change to
setting 02.
Shorter
○
Enable
Enable or disable the fi lter indicator.
Disable
Setting 02 is for use with a central
remote controller.
controller
○
Default
Adjust the horizontal swing airfl ow
direction.
Left half
(For horizontal swing equipped
models)
Right half
○
Default
Adjust the cool air trigger tempera-
ture. To lower the trigger tempera-
Adjust (1)
ture, use setting 01. To raise the
trigger temperature, use setting 02.
Adjust (2)
2012-7-13 10:52:50 2012-7-13 10:52:50