AirStage 9367702107 Installationsanleitung Seite 15

Function
Function Setting number
number
00 Default
Heat air
01 Adjust (1)
tem-
31
perature
02 Adjust (2)
trigger
03 Adjust (3)
00 Enable
Auto
40
restart
01 Disable
00 Super low
Cool Air
43
Prevention
Follow the
setting on
01
the remote
controller
00 Start/Stop
External Emergency
46 01
control stop
02 Forced stop
00 All
Error re-
47
Display only on
port target
01 central remote
controller
Follow the
setting on the
Fan set-
00
remote control-
ting when
ler
cooling 49
thermostat
OFF
01 Stop
7.4.1. Button name and function
OPERATION indicator lamp (Green)
TIMER indicator lamp (Orange)
FILTER indicator lamp (Red)
9367702107-01_IM.indb Sec1:14 9367702107-01_IM.indb Sec1:14
Default Details
○
Adjust the heat air trigger temperature.
To lower the trigger temperature by
11 degrees F (6 degrees C), use setting
01. To lower the trigger temperature by
7 degrees F (4 degrees C), use setting
02. To raise the trigger temperature,
use setting 03.
Enable or disable automatic system
restart after a power outage.
* Auto restart is an emergency
function such as for power failure
etc.
Do not start and stop the indoor
unit by this function in normal
operation.
○
Be sure to operate by the control
unit, converter or external input
device.
○
Restrain the cold airfl ow with making
the airfl ow lower when starting
heating operation. To correspond to
the ventilation, set to 01.
○
Allow an external controller to start
or stop the system, or to perform an
emergency stop.
* If an emergency stop is performed
from an external controller, all
refrigerant systems will be disabled.
* If forced stop is set, indoor unit
stops by the input to the external
input terminals, and Start/Stop by a
remote controller is restricted.
○
Change the target for reporting er-
rors. Errors can either be reported in
all locations, or only on the central
remote controller.
When set to 01, the fan stops when
○
the thermostat is OFF in cooling
operation. Connection of the wired
remote controller (2-wire type or
3-wire type) and switching its therm-
istor are necessary.
MANUAL AUTO button
7.4.2. Checking the function settings
Press and hold the "MANUAL AUTO" button on the indoor unit for 3 seconds to check
the function settings. It is necessary to disconnect the power in order to return to normal
operation mode.
(1) Indoor unit and refrigerant address indication
Indication pattern
Indicator name
OPERATION indicator lamp (Green)
TIMER indicator lamp (Orange)
FILTER indicator lamp (Red)
• Indoor unit address example
(Example) ADDRESS : 24
1 cycle 12 sec
OPERATION
ON
indicator
lamp (Green)
OFF
TIMER ON
indicator 0.5s 0.5s 0.5s 0.5s
lamp (Orange) OFF
ON
FILTER
0.5s 0.5s 0.5s 0.5s 0.5s 0.5s 0.5s 0.5s
indicator
lamp (Red) OFF
• Indoor unit address example Refrigerant address example
(Example) ADDRESS : 30
1 cycle 12 sec
OPERATION
ON
indicator
1.0s
1.0s 1.0s
lamp (Green)
OFF
TIMER ON
indicator 0.5s 0.5s 0.5s 0.5s 0.5s 0.5s
lamp (Orange) OFF
ON
FILTER
indicator OFF
OFF
lamp (Red)
• Setting details
Function number Item
01 Indoor unit address
02 Refrigeration address
For use with a remote controller, set all rotary switches to 0, and refer to "7.1. Setting the
address" for details.
All switches are set to 0 at the factory.
(2) Others
Indication pattern
Indicator Name
Function number; tens place
OPERATION indicator lamp (Green)
(0.5s ON/0.5s OFF)
Function number; ones place
TIMER indicator lamp (Orange)
(0.5s ON/0.5s OFF)
FILTER indicator lamp (Red) Setting number: (0 to 9) (0.5s ON/0.5s OFF)
(Example) Function : 31, Setting number : 2
1 cycle 12 sec
OPERATION
ON
indicator
0.5s 0.5s 0.5s 0.5s 0.5s 0.5s
lamp (Green)
OFF
ON
TIMER
indicator 0.5s 0.5s
lamp (Orange)
OFF
ON
FILTER
0.5s 0.5s 0.5s 0.5s
indicator
OFF
lamp (Red)
Indication pattern
Indoor unit
Refrigerant address
address
ON Flash (1.0s ON/1.0s OFF)
Address: tens place (0.5s ON/0.5s OFF)
Address: ones place (0.5s ON/0.5s OFF)
ON
10 sec
8 sec
1.0s 1.0s 1.0s
1.0s
9 sec
Setting number
00 to 63
00 to 99
Indication pattern
9 sec
11 sec
10 sec
En-14
2012-7-13 10:52:51 2012-7-13 10:52:51