Thomashilfen RECARO Monza Nova 2 Reha Montage- Und Gebrauchsanleitung Seite 9

RECARO Monza Nova 2 Reha – Instructions for assembly and use (supplement)
Stabilising bow, rear (for swivel base) (accessory)
Please note our separate instructions for mounting! Download: www.thomashilfen.com
Stand, front (for swivel base) (accessory)
Please note our separate instructions for mounting! Download: www.thomashilfen.com
Back stabilisers (accessory)
The back stabilisers prevent the back from dropping. Please note our separate instructions for mounting! Download: www.thomashilfen.com
Footrest, short 12 cm / 4.7" (accessory)
Footrest, long 18 cm / 7.1" (accessory)
Assembly:
Remove the two caps at the front bottom part of the seat before attaching the footrest. Push the footrest tubes into the RECARO Monza Nova 2 Reha car seat. Press in the
catch spring and push the tubes in further until you hear the catch spring audibly engage.
Secure the footrest using the belt that runs around the seat bottom of the RECARO Monza Nova 2 Reha. In order to do so, open the buckle under the seat and loop the
front section of the belt around the crossbar of the footrest. Make sure that the belt is fastened correctly. Use the sliding buckle to adjust the belt length as required.
To stabilize the footrest on the vehicle floor adjust the height of the support bars by screwing them in or out until they have contact with the vehicle. Then lock the
support bars with the hand knobs to prevent them unscrewing accidentally. Screw the hand knobs upwards as far as possible and tighten them fast.
Disassembly:
Release the belt under the seat surface of the RECARO Monza Nova 2 Reha. Press in the catch spring with a slender object (e.g. ballpoint pen) and pull the footrest tubes
completely out of the guide. Refasten the belt under the seat surface of the RECARO Monza Nova 2 Reha.
Please note: If the swivel base is being used the footrest is attached to the footrest adapter integrated in the swivel base. In this case, make sure to always secure the
footrest against falling off with the hand knob provided with the user manual. The receiver for the hand knob (metal block with thread) is situated on the left tube of the
footrest adapter.
Lower leg length: The lower leg length is adjusted by changing the height of the footrest. Loosen both outer screws. Retighten them after each adjustment.
Foot angle: Loosen the four screws left and right on the underside of the footrest to adjust the desired foot angle with the rails. Then retighten the screws.
Please note: The footrest cannot be used in combination with the seat depth extension, unless the swivel base is used in addition.
Note: If the footrest should firmly be screwed to the seat, the "footrest adapter" (item code: 821) is required.
Fig. 6a: Remove the caps + insert the rest
Fig. 6d: Secure with belt
Seat wedge, bottom (accessory)
The seat wedge is positioned centrically below the car seat. The high edge is at the front to achieve an optimum rest position of the child.
The cover can be removed (zipper) and washed in the machine at up to 30° C / 86° F.
Please note: Function of the swivel base is considerably reduced if being used in combination with the seat wedge. We therefore do not recommend using seat wedge
and swivel base at the same time.
Fig. 7a: Positioning seat on seat wedge
Seat wedge, inside (accessory)
The seat wedge (inside) can be fastened to the seat surface at 3 different positions:
1. An active posture is achieved by placing the seat wedge on the seat with the high side facing the back.
2. Velcro-fasten the seat wedge with the flat side facing rearwards for a more passive posture / rest position.
3. In order to reduce the seat depth or to achieve a bigger hip angle, you can also Velcro-fasten the seat wedge to the rear of the seat in an upright position with the broad
side facing downwards.
The two lateral pads for additional protection are Velcro-fastened to the sides.
The cover can be removed (zipper) and washed in the machine at up to 30° C / 86° F.
Fig. 8a: Active
Seat depth extension + 13 cm / 5.1" (accessory)
Remove the two caps at the front bottom part of the seat before attaching the seat depth extension. Press the catch springs in at the rear ends of the sliding rods and push
the tubes into the holes as far as they will go.
Secure the seat depth extension with the belt that runs around the seat bottom of the RECARO Monza Nova 2 Reha. In order to do so, open the buckle under the seat and
guide the front section of the belt through the belt loop on the seat depth extension. Make sure that the belt is fastened correctly. Use the sliding buckle to adjust the belt
length as required.
Please note: The seat depth extension cannot be used in combination with the footrest or swivel base, unless the swivel base is used in addition.
The cover can be removed (cord) and washed in the machine at up to 30° C / 86° F.
Fig. 9a: Removing caps
Table (accessory)
Slide the table onto the two sides of the seat surface. The table is fastened on both sides with two Velcro strips each. Guide the Velcro strips of the table through the
plastic rings at the seat / seat back (pelvic belt).
The cover can be removed (zipper) and washed in the machine at up to 30° C / 86° F.
Fig. 10a: Attaching the table
Fig. 6b: Press in catch spring
Fig. 6e: Press in catch spring to disassemble
Fig. 7b: Final position
Fig. 8b: Passive
Fig. 9b: Pressing in the catch springs
Fig. 10b: Attaching belts to seat
Fig. 6c: Release belt below seat
Fig. 6f: Adjust height to suit vehicle
Fig. 8c: Back
Fig. 9c: Release belt below seat
item code: 819
item code: 817
item code: 816
item code: 806
item code: 805
item code: 810
item code: 809
Fig. 8d: With lateral pads
item code: 808
Fig. 9d: Secure with belt
item code: 811
9