Kärcher B 140 R Originalbetriebsanleitung Seite 24

Setting the language
Sit on the seat and set main switch to "1".
Select the cleaning program "driving".
Press and hold the Info key.
Set main switch to "0".
The display shows the language selection.
Release the info button and select the
language by rotating the info button.
Confirm the selected language setting by
momentarily pressing the info button.
The language will be taken over and the ap-
pliance will shut off.
Settings
You can make the settings for the different
cleaning programs in the operator menu.
Different parameters can be set based on
the cleaning program. The settings are
done using the Info button.
Operations menu
Sit on the seat and set main switch to "1".
The display shows the battery charging
status.
Select cleaning program.
Call the operator menu by turning the
info button.
Select the desired parameter by turning
the Info button. The currently set value
is displayed as a bar.
Press Info button, the bar display
blinks.
Reset the parameter by turning the Info
button between "min" and "max".
Accept modified setting by pressing the
Info button or wait till the set value is ac-
cepted automatically.
Note
If the selected parameter does not change
within 10 seconds, then the display goes
back to displaying the battery charging sta-
tus and the fresh water level.
The same cleaning parameter can have in-
dividual settings for each cleaning pro-
gram.
The brush pressure can be set only when
the machine is on in the programs brush
suction, wet brushing, polishing and polish-
ing suction.
All settings are saved in the powerless
state of the machine.
24
Reset parameters
Select the menu item "Accept default
values?" in the operator menu by turn-
ing the Info button
Press Info button. The factory settings
of all parameters are restored for each
cleaning program.
Adjustable min:step:
parameters max
Water quantity 1:1:8
Dosing equip- 0,5%:0,5
ment for deter- %: 3%
gent (optional)
Brush pressure 0:1:8
FACT (brush –
speed)
(Only with R
cleaning head)
Brush rotation 0s:1s:3s
time after stop
Working speed 1:1:8
Low noise (re- –
duced suction)
The table given below gives details of the
factory settings of the parameters for the
cleaning programs. If no values are en-
tered, then the respective parameter can-
not be set in the given cleaning program.
Factory setting
Scrubbing suction 5
Wet scrubbing 5
Dry vacuum cleaning –
Polishing –
Polish suction –
7
-
EN
Remark
1=min.,
8=max.
0,5=min.,
3=max.
0=min.,
8=max.
Scrubbing suction
Wet scrubbing
Power-,
Whisper-, Polishing
Fine
Polish suction
Clean
P=Power Clean
From
Switch on the dosing equipment for
idling to
lifting detergent (optional)
1=1km/h,
Activate the switch for detergent dosing.
8=6km/h
Detergent gets added automatically.
0/1
Note
You can set the detergent dosing in the Op-
erations menu.
Note
As soon as the detergent pump starts run-
ning, this is indicated through a blinking "C"
in the display.
Setting the Vacuum Bar
Oblique position
To improve the vacuuming result on tiled
floors the vacuum bar can be turned to an
oblique position of up to 5°.
Release the wing nuts.
Turn the vacuum bar.
4 4
4 4
– 4
4 4
4 4
Tighten the wing nuts.
Inclination
If the vacuum result is unsatisfactory the in-
clination of the straight vacuum bar can be
modified.
Release the wing nuts.
Tilt the vacuum bar.
1% P 2s 1
1% P 2s 1
– P 0s –
– P 0s 1