Installation Instructions - Sharp Ebr-5000Al Anweisungen

- Utilization of the package w ill m ake installation easier.
1. (For U.K. use)
A cut-out w ill have to be provided in the right side of the kitchen cabinet for the plug of the oven.
N.B.The m ains plug m ust be accessible after installation or an all-pole sw itch disconnection m ust be
provided w ith a contact separation of at least 3 m m in each pole.
(For Continental use)
The electric outlet m ust be installed at 150 m m high from the floor of the built-in cabinet and at 50 m m
from the right w all of the built-in cabinet as show n in Fig. 1. The m ains plug m ust be accessible after
installation or the oven m ust be connected to an electric circuit provided w ith an all-pole sw itch (contact
gap no less than 3 m m ) to disconnect the oven in case of danger. A safety-device such as a fuse in the
installation m ay be used as a sw itch.
2. Rem ove the built-in kit from the package. Set the package of the built-in kit as it w as.
3. Place the oven on the package of the built-in kit as show n in Fig. 3.
Caution:
4. Attach the alum inium sheet
Set the spacing brackets
a distance of 17 m m betw een the front end of the shelf and the spacing brackets, and attach them
w ith the four screw s
Caution:
5. Insert tw o tabs of the intake duct
And install the intake duct
6. Loosen screw
7. Install the exhaust duct
6) as show n in Fig. 4.
8. Loosen screw
9. Rem ove screw
10. Let the pow er supply cord pass through the hole of the low er side of the intake duct
11. Install the intake duct
at step 9) as show n in Fig. 5.
Caution:
12. Rem ove the backing paper from the three cushions
left side of the intake duct
show n in Figs 6-a and 6-b. Attach the cushion
13. (For U.K. use)
Place the oven on the spacing brackets on the shelf of the kitchen cabinet feeding the pow er supply cord
through the prepared cut-out.
(For Continental use)
Place the oven on the spacing brackets on the shelf of the kitchen cabinet.
14. Connect the oven to the pow er supply.
Caution: a. In the U.K., connect the oven to the pow er supply 230-240 V, 50 Hz.
15. Adjust the position of the oven so that the feet fit into the recesses of the spacing brackets as show n in
Fig. 2.
Caution:
16. Place the built-in fram e elem ent
horizontally. Secure loosely to the kitchen cabinet w ith tw o screw s
17. Insert tw o built-in fram e side elem ents
Secure tw o screw s
left built-in fram e side elem ents
Note: Align parts
18. Install the second built-in fram e elem ent
the oven. Secure the built-in fram e elem ent
to the kitchen cabinet w ith tw o screw s
Caution:
Downloaded from: http://www.usersmanualguide.com/

INSTALLATION INSTRUCTIONS

M ake sure that the oven alw ays keeps its balance to avoid falling over.
C
onto the back panel
1
on the shelf along the right and left w alls of the kitchen cabinet, keeping
0
, as show n in Fig. 1.
The arrow m arks on each spacing bracket should be pointing tow ards you.
3
3
to the back plate
F
holding the outer w rap to the rear of the oven as show n in Fig. 4.
2
to the rear of the oven by tightening tw o screw s
G
holding the back plate
H
from the oven as show n in Fig. 4.
4
to the rear of the oven w ith tw o screw s
Avoid pinching the pow er supply cord betw een the oven and the intake duct
4
and attach the cushion
b. In the Continent, connect the oven to the pow er supply 230 V, 50 Hz.
M ake sure that the pow er supply cord does not touch the air vent openings behind the oven.
8
B
tightly as show n in Fig. 7. Check location by m easuring distance betw een right and
9
8 9
and as indicated in Fig. 7. Such that screw s
M ake sure that the 7.5 m m of the fram es (upper and low er) and cabinet overlap each other
as show n in Fig. 9, or the kitchen cabinet door m ay touch the built-in fram e elem ents.
D
of the built in cabinet as show n in Fig. 1 and Fig. 2.
into the slits of the back plate
E
w ith one screw
E
to the rear of the oven as show n in Fig. 4.
5 6
, and
7
at the left side of the cushion
5
at the top of the oven as show n in Figs 6-a and 6-b.
on top of the oven m aking sure that it is level both vertically and
9
betw een the built-in fram e elem ent
. The distance is stated in Fig. 8.
8
over the built-in fram e side elem ents
8
through the holes of the built-in fram e side elem ents
B
as show n in Fig. 7.
2
E
.
A
as show n in Fig. 4.
F
A
and (loosened at step
4
as show n in Fig. 5.
G
(loosened at step 8) and
7 6
. Attach the cushion
6
and the oven as
B
as show n in Fig. 7.
8
and the kitchen cabinet.
B
can be fixed into position.
9
at bottom edge of
H
(rem oved
4
.
at the top and
9