Installation Instructions - Sharp EBR-4900 Installationsanleitung

1. (For U.K. use)
A cut-out will have to be provided in the side of the kitchen cabinet for the plug of the oven.
N.B.The mains plug must be accessible after installation or an all-pole switch disconnection must be
provided with a contact separation of at least 3 mm in each pole.
(For Continental use)
The electric outlet must be installed at 150 mm high from the floor of the built-in cabinet and at 50 mm
from the right wall of the built-in cabinet as shown in Fig. 1. The mains plug must be accessible after
installation or the oven must be connected to an electric circuit provided with an all-pole switch (contact
gap no less than 3 mm) to disconnect the oven in case of danger. A safety-device such as a fuse in the
installation may be used as a switch.
2. Remove the built-in kit from the package.
3. Set the spacing brackets
a distance of 17 mm between the front end of the shelf and the spacing brackets, and attach them
with the four screws
Caution:
4. Remove one screw
the tab of the back plate
5. Loosen two screws
6. Install the exhaust duct
5) as shown in Fig. 3.
7. Insert the tab of the back plate
rear of the oven with one screw
Caution:
8. Remove screw
9. Let the power supply cord pass through the hole of the lower side of the intake duct
10. Install the intake duct
in Fig. 4.
Caution:
11. Remove the backing paper from the three cushions
left side of the intake duct
shown in Figs 5-a and 5-b. Attach the cushion
12. (For U.K. use)
Place the oven on the spacing brackets on the shelf of the kitchen cabinet feeding the power supply cord
through the prepared cut-out.
(For Continental use)
Place the oven on the spacing brackets on the shelf of the kitchen cabinet.
13. Connect the oven to the power supply.
Caution: a. In the U.K., connect the oven to the power supply 230-240 V, 50 Hz.
b. In the Continent, connect the oven to the power supply 230 V, 50 Hz.
14. Adjust the position of the oven so that the feet fit into the recesses of the spacing brackets as shown in
Fig. 2.
Caution:
15. Place the built-in frame element
horizontally. Secure loosely to the kitchen cabinet with two screws
16. Insert two built-in frame side elements
Secure two screws
left built-in frame side elements
Note: Align parts
17. Install the second built-in frame element
the oven. Secure the built-in frame element
to the kitchen cabinet with two screws
Caution:
Downloaded from www.Manualslib.com

INSTALLATION INSTRUCTIONS

1
on the shelf along the right and left walls of the kitchen cabinet, keeping
9
, as shown in Fig. 1.
The arrow marks on each spacing bracket should be pointing towards you.
E
holding the back plate
F
from the slit of the rear of the oven.
G H
and holding the outer wrap to the rear of the oven as shown in Fig. 3.
2
to the rear of the oven by tightening two screws
F
into the slit of the rear of the oven. And install the back plate
E
(removed at step 4) as shown in Fig. 3.
E
Fasten screw loosely for step 10.
J
from the oven as shown in Fig. 3.
3
to the rear of the oven with two screws
Avoid pinching the power supply cord between the oven and the intake duct
3
and attach the cushion
Make sure that the power supply cord does not touch the air vent openings behind the oven.
7
on top of the oven making sure that it is level both vertically and
0
tightly as shown in Fig. 6. Check location by measuring distance between right and
8
. The distance is stated in Fig. 7.
7 8
and as indicated in Fig. 6. Such that screws
Make sure that the 7.5 mm of the frames (upper and lower) and cabinet overlap each other
as shown in Fig. 8, or the kitchen cabinet door may touch the built-in frame elements.
manuals search engine
F
to the rear of the oven as shown in Fig. 3. And release
4 5 6
, and
6
at the left side of the cushion
4
at the top of the oven as shown in Figs 5-a and 5-b.
8
between the built-in frame element
7
over the built-in frame side elements
7
through the holes of the built-in frame side elements
0
as shown in Fig. 6.
2
G H
and (loosened at step
3
as shown in Fig. 4.
E J
and (removed at step 8) as shown
5
. Attach the cushion
5
and the oven as
0
as shown in Fig. 6.
7
and the kitchen cabinet.
0
can be fixed into position.
8
at bottom edge of
F
to the
3
.
at the top and
8