Handterminal; Menüstruktur - Emerson Rosemount 2160 Betriebsanleitung

Betriebsanleitung
00809-0105-4160, Rev AC
September 2010

HANDTERMINAL

Menüstruktur
1. Overview 1. Active Alerts
2. Communication Status
3. PV – 1.0=Wet /0.0=Dry
4. PV Status
5. Last Update Time
2. Configure 1. Guided Setup
2. Manual Setup
3. Alert Setup
3. Service Tools 1. Alerts
2. Variables
3. Communications
4. Maintenance
5. Simulate
(*1) Diese Option erscheint, wenn vorherige Alarmmeldungen vorliegen.
(*1) This Option Appears When There Are Previous Alerts.
(*2) Only One Option Appears Depending On Which Has Been Selected.
(*2) Je nach Auswahl wird nur eine Option angezeigt.
1. Join Device To Network 1. Network ID
2. Configure Update Rate 2. Join Device To Network
3. Configure Device Display 3. Broadcast Rates
4. Configure Alerts 4. Power Mode
5. Basic Setup 5. Power Source
1. Application
1. Wireless
2. Sensor
2. Operation
3. Device Temperature 1. Electronics Temperature
4. Device Information
1. Tag
5. Device Display
2. Long Tag
6. Other
3. Device
4. Radio
5. Write Protect
1. Mode
2. Display Options
1. Measurement and Status Log
1. Alert 1 1. Configure Alert 1
2. Mode
2. Alert 2
3. Variable
3. Alert 3
4. Direction
4. Alert 4 5. Limit
6. Band
1. Configure Alert 2
1. Active Alerts
2. Mode
2. History (*1)
3. Variable
4. Direction
1. PV – 1.0=Wet /0.0=Dry 5. Limit
2. PV Status 6. Band
3. Sensor Frequency
4. Sensor Frequency Status 1. Configure Alert 3
5. Electronics Temperature 2. Mode
6. Electronics Temperature 3. Variable
Status
4. Direction
7. Supply Voltage 5. Limit
8. Supply Voltage Status 6. Band
9. Last Update Time
1. Configure Alert 4
2. Mode
1. Join Status
3. Variable
2. Communication Status
4. Direction
3. Join Mode
5. Limit
4. Number of Available Neighbors
6. Band
5. Number of Advertisements Heard
6. Number of Join Attempts
1. Diagnostics
2. Counters / Timers
3. Calibrate
4. Others
1. Sensor Output Mode
2. Fork Frequency
3. Electronics Temperature
4. Supply Voltage
1. Sensor Calibration
2. Reset Calibration
3. Sensor Compensation
1. Perform Master Reset
2. Measurement History
3. Advertise to New Devices
4. Load User Defaults
Rosemount 2160
1. Configure Update Rate
2. Message 1
1. Operation Mode
2. Sensor Output Delay
3. Media Density
1. Sensor Stabilization Time
2. Measurement Time
3. Allowable Change In
Dry Fork Frequency
4. Sensor Fault Delay
1. Unit
2. Maximum
3. Minimum
1. Manufacturer
2. Device Type
3. Final Assembly Number
4. Universal
5. Field Device
6. Software
7. Hardware
8. Descriptor
9. Message
10.Date
11.Model Number
12.SI Unit Restriction
13.Country
14.Device ID
1. Manufacturer
2. Device Type
3. Device Revision
4. Software Revision
5. Hardware Revision
1. Sensor Frequency
2. Temperature Compensation
3. Uncompensated Frequency
4. Sensor State
1. Dry Fork Frequency
2. Dry to Too Dry
3. Dry to Indeterminate
1. Sensor
4. Wet to Indeterminate
2. Sensor Status
5. Wet to Too Wet
3. Dry Fork Frequency /
6. Zero
Switch Points
1. Sensor Wet Count
1. Counters
2. Calibration Count
2. Timers
3. Fault Control
1. Time Since Output Change
2. Total Time Dry
3. Total Time Wet
1. Dry Fork Frequency
2. Sensor Frequency
3. Calibrate Dry Fork
4. Sensor Calibration Status
5. Calibration Count
1. Restore Factory Calibration
2. Restore Site Calibration
1. Calibration Temperature
2. Temperature Compensation
3. Process Temperature
1. Burst Option 1
2. Update Rate 1
(*2)
2-7