Remote Controller And Its Functions - Toshiba RAV-SM562XT-E Betriebsanleitung

REMOTE CONTROLLER AND ITS FUNCTIONS

(1) Infrared signal emitter
Transmits a signal to the indoor unit.
(2) START/STOP button
Push the button to start operation.
(A receiving beep is heard.)
Push the button again to stop operation.
(A receiving beep is heard.)
If no receiving sound is heard from the indoor
unit, push the button twice.
(3) Mode select button (MODE)
Push this button to select a mode.
Each time you push the button, a mode is
selected in a sequence that goes from A : Auto
changeover control,
: Heat, : Fan only, and back to A.
(A receiving beep is heard.)
(4) Temperature button (
, ....... The set temperature is increased up to
30°C.
9 ....... The set temperature is dropped down to
17°C.
(A receiving beep is heard.)
(5) Fan speed button (FAN)
Push this button to select fan speed. When you
select AUTO, the fan speed is automatically
adjusted according to the room temperature.
You can also manually select the desired fan
speed from among five settings.
(LOW , LOW
MED +
(A receiving beep is heard.)
(6) Auto louver button (SWING)
Push this button to swing the louver.
(A receiving beep is heard.)
Push the SWING button to stop the louver
swinging. (A receiving beep is heard.) (to see
page 13.)
(7) Set louver button (FIX)
Push this button to adjust the air flow direction.
(A receiving beep is heard.)
While this button is kept depressed, the
receiving tone continuously sounds. (to see
page 13.)
(8) Off timer button (OFF)
Push this button to set the OFF timer.
(9) On timer button (ON)
Push this button to set the ON timer.
(10) Reserve button (SET)
Push this button to reserve time settings.
(A receiving beep is heard.)
(11) Cancel button (CLR)
Push this button to cancel ON timer and OFF
timer. (A receiving beep is heard.)
(12) High power button (High POWER)
Push this button to start the high power
operation. (to see page 10.)
: Cool, : Dry,
)
+ , MED ,
, HIGH )
(13) Memory button (MEMO)
Push this button to stand by memorizing the
settings.
Push the button again for more than 3 seconds to
memorize the setting indicated on the remote
controller and
12.)
(14) Automatic operation button (AUTO)
Push this button to operate the air conditioner
automatically.
(A receiving beep is heard.) (to see page 15.)
(15) ECO timer button (ECO)
Push this button to start the ECO timer (OFF
timer) operation.
You can select the OFF timer time from among
four settings (1, 3, 5 or 9 hours). (to see page 15.)
(16) FILTER button
Push this button to turn off the filter cleaning lamp
on the indoor unit.
Push this button after cleaning the air filter.
(to see page 17.)
(17) PRESET button
Push this button to operate the air conditioner
according to settings memorized by the MEMO
button. (to see page 12.)
(18) TIMER button
Use this button to change the clock, ON timer, and
OFF timer times.
To forward the time, push the "TIMER
To set back the time, push the "TIMER
(4)
(2)
(5)
(6)
SWING
(7)
(9)
ON
(8)
(16)
4
mark is indicated. (to see page
(1)
AUTOA
A
B
PRESET
START/STOP
AUTO
FAN MODE
ECO Hi-POWER
TIMER
FIX MEMO
OFF SET CLR
FILTER
RESET CLOCK CHECK
" button.
" button.
(17)
(3)
(14)
(15)
(12)
(13)
(11)
(10)
(18)