Inhaltsverzeichnis
Werbung
1. TECHNICAL FEATURES
MODEL
MES150
Capacity
Kg
150
Lifting height(h1)
mm
1420
Min .fork height
mm
130
Fork width
mm
330/520
Wheels Q'ty
N
4
Lifting speed
m/s
Without load 82 mm/s, with full load 67 mm/s
Lowering speed
m/s
Without load 89 mm/s, with full load 96 mm/s
Battery
7 Ah/12v
Front wheel
mm
Ø 75*32
Rear wheel
mm
Ø 100*32
Weight
kg
58
2. ADVISES
2.1 Read this instruction carefully before using the stacker. If necessary,
please call our technical people for assistance.
2.2 Move the stacker always keeping the forks at the lowest position while no
loading on the forks. Pay attention not to hurt anybody around your
working area.
2.3 People are forbidden to stand on the forks of the stacker. Do not leave
the stacker on the working place after used. The load capacity of the
stacker depends on the lifting height and the position of the load center,
please refer to the relative technical features in this instruction.
2.4 The adhesive label on the stacker must be always legible. Do not use the
stacker for purpose except lifting or lowering load.
2.5 Do not make casual repair. If repaired by unprofessional people, the safety
modulus of the machine could be altered. In case damage happens,
repair it in the local place according to the instruction or contact to us.
2.6 Carry out all the work and maintenance according to the norms after
using it.
3. WORKING NORMS FOR THE OPERATOR
Do not worry about how to operating this stacker, the characteristic of this
stacker is facility and easy to operate.
3.1 The two function of the brakes
The rear wheels are equipped with brakes which with two functions, it
can control the moving of forward and backward effectively. Step the
pedal of the brake backward, the stacker will be braked. Step the pedal of
the brake forward, the stacker will travel normally. The stacker should be
braked under the condition as following: A, stop at the slope; B, during
charging; C, when loading; D, leave unused.
3.2 The forward/backward/swivel of the stacker
Open the brake of the rear wheels, leave the two wheels at the state which
can swivel freely. Take hold of the armrest, push the stacker ahead, the
stacker can move ahead. In the same way, pull the stacker backward,
the stacker will fall back. We use universal wheels on this truck, so it's
very easy to swivel and swivel into any direction. It's only need a small
space because it can be freely swiveled at the original position. If one of
the brake is locked, the stacker will be swiveled on an even keel
according to the centre of a circle.
3.3 Lifting and lowering of the forks
Press the button of power to "ON", then press the "<" or ">" to control the
lifting and lowering of the stacker. (Attention: Before lifting or lowering the
forks with load on the forks, please lock the rear wheels of the stacker to
avoid moving of the stacker during lowering and lowering.)
3.4 Load of the stacker
According to the deferent goods, this stacker can use the three kinds of
shelves as double forks, single fork, and platform. The ways of how to use
these shelves are as follows:
A. Double forks ( be fitted for lifting the common load)
(1) Drive close to the load.
(2) Lift the forks below the load.
(3) Drive forward, bringing the forks under the load.
(4) Lift the load to get the load.
(5) Back the stacker with the load to make the descent if possible.
(6) Lower the load slowly.
B. Single fork (be fitted for lifting the cylindraceous load)
(1) Drive close to the load.
(2) Drive the fork to the centre of the circle of the load.
(3) Drive forward, extend the fork inside the cylinder.
(4) Lift the load to get the load.
(5)
Back the stacker with the load to make the descent if possible.
(6)
Lower the load slowly.
C. Platform (be fitted for the lifting the load with small volume)
(1) Drive close to the load.
(2) Lift the platform to a proper position (be convenient for people to
stack the goods)
(3) Transfer the goods to the platform artificially.
(4) Lower the platform.
Attention: If possible, the platform with load can be lifted as the double
forks.
3.5 The steps of unloading the goods
A. Double forks/ single forks
(1) Get close to the position.
(2) Lift the load up to the desired height position.
(3) Advance slowly to bring the load to the proper position.
(4) Lower the load to make the bottom of the forks on the shelf.
(5) After unloaded, back the forks slowly.
B. Platform
(1) Drive the stacker with load to the destination, and lock the rear wheels.
(2) Lift the platform to a proper height for people to unload it.
(3) Unloading.
4. RECHARGE OF BATTERY
The batteries of the stacker must be recharged with a constant
continuity, and the recharging should be very timely.
When recharging, switch off the power. Connect the charger to the power supply,
and insert the plug of the charger into the recharging faucet of the stacker,
press the switch of charger, recharging will begin. When recharging is over, the
charger will stop automatically.
5. DAILY MAINTENANCE
The daily maintenance is a responsibility of the operator of the stacker. The main
functions that must been checked are as follows:
1
Check the retarder of the motor.
2
Check the forks.
3
Check the swivel wheel.
4
Check the transmission belt.
5
Check the charger.
2 | 01252 359760 • ajproducts.co.uk
Werbung
Inhaltsverzeichnis
