Saw Storage; Tips And Tricks - Metabo TS 216 Originalbetriebsanleitung

45°
2. Lock the set angle of inclination by tightening
the clamping lever (19).
3. Check angle of inclination:
– 0° = at right angles to the saw table
– 45° with separate mitre square.
If these angles are not achieved exactly:
4. Release cross-head screw (47) at respective
cam disc and adjust cam plate until the blade
bevel angle in relation to the saw table is
exactly 0°,
(= right angles), or 45°, in the end positions.
5. Retighten cross-head screw at cam plate.
6. After adjusting the stop limitation, readjust
angle scale at front side if necessary.
Note:
To set the bevel angle limitation of -1.5° to 46.5°,
the blade tilt stop lever must be pulled out.

10.3 Saw storage

Danger!
Store the machine beyond the reach of
children. Store the machine such that it
cannot be put into operation by unauthorised
personnel and such that the stationary
machine cannot cause injury.
Caution!
Do not store the tool outdoors or in damp
conditions without protection.
10.4 Maintenance
Saw Cleaning
 Remove chips and saw dust with vacuum
cleaner or brush:
– from saw blade setting guide elements;
– from motor vent slots;
– chip case.
– Height adjustment
– Swivel guide
Before switching ON
Visual check to see if
– distance between saw blade and splitting
wedge is 3 to 8 mm.
– Splitting wedge is in line with saw blade.
Visual check of power cable and power cable
plug for damage; if necessary have damaged
parts replaced by a qualified electrician.
Every time the machine is switched off
Check whether the saw blade overrun exceeds
10 seconds; if the overrun is longer than this,
have the motor replaced by a qualified electrician.
Monthly (if used daily)
Remove saw dust and chips with vacuum or
brush; apply light coat of oil to guide elements:
– Threaded rod and guide rods of blade rise and
fall mechanism;
– Swivel segments.
Every 150 hours of operation
Check all screwed joints, retighten if necessary.
If necessary:
Set table leg guide bushings.
 Allen screws (48)
turn clockwise =
guide sluggish
 Allen screws (48)
turn anti-clockwise =
guide moves easily.
 Further fine adjustment by means of a setscrew.
(49)
47
20
19
48
Setting guide bushings on front leg mount:
 Turn Allen screws (50) clockwise = guide
sluggish.
 Turn Allen screws (50) anti-clockwise =
guide moves easily.
Setting guide bushings on rear leg mount:
 Turn Allen screws (51) clockwise = guide
sluggish.
 Turn Allen screws (51) anti-clockwise = guide
moves easily.
Tighten all Allen screws diagonally and
evenly.

11. Tips and Tricks

 Before cutting a workpiece to size make trial
cuts on pieces of scrap.
 Always place a workpiece on the saw table in
such way that it cannot tilt or rock (e.g. always
place a curved board on the table with the convex
side up).
 For efficient cutting of same-length cuts, use a
length stop.
 Keep surface of table clean.
12. Troubleshooting
Danger!
Before carrying out any fault service or
maintenance work, always:
1.Switch machine off.
2.Disconnect from the power supply.
3.Wait for saw blade to come to standstill.
Check that all safety devices are operational
again after each fault service.
Motor does not run
The restart protection is active. If the mains plug
is inserted with the machine switched on, or if the
current supply is restored following an
interruption, the machine does not start up:
49
 Switch the machine off and back on again.
No mains voltage:
 Check cables, plug, outlet and
mains fuse.
Motor overheated, e.g. by a blunt saw blade or
chip build-up in the chip case:
 Remove cause for overheating, let cool off for a
few minutes. Then restart machine.
Speed is not reached
Overload protection: There is a MAJOR reduction
in load speed.
 The motor temperature is too high! Allow the
machine to run at idle speed until it has cooled
down.
Overload protection: There is a SLIGHT reduction
in load speed.
 The machine is overloaded. Reduce the load
before continuing to work.
Specified maximum no-load speed is not reached
- motor not receiving sufficient mains voltage:
50
 Use a shorter feed line or cable with larger cross
section
( 1.5 mm
 Have power supply checked by a qualified
electrician.
Loss of cutting performance
Saw blade blunt (possibly tempering marks on
blade body):
 Replace saw blade (see chapter 10.
Maintenance).
Chip ejection blocked
No dust extraction unit connected or suction
capacity insufficient:
 Connect dust extraction unit or increase suction
capacity (air speed  20 m/sec at chip ejection
tube).
13. Accessories
Use only original Metabo accessories.
Use only accessories which fulfil the requirements
and specifications listed in these operating
instructions.
Circular saw blade Precision Cut, order no.:
6.28062
– Very wide range of applications in wood
processing
– For very good, clean cutting results for straight
51
and cross cuts in soft and hard wood
Circular saw blade Multi Cut, order no.: 6.28063
– Universal use for demanding materials
– Ideally suited for many applications in interior
construction
– Perfect cutting results also for cross cuts in solid
wood, uncoated, coated or veneered chip
board, MDF
– When high cutting quality is required, e.g.
laminate, plastic, thin-walled aluminium, copper,
and brass profiles
For a complete range of accessories, see
www.metabo.com or the catalogue.
14. Repairs
For safety reasons, repairs to power tools
must be carried out by qualified electricians
only using original spare parts!
If you have Metabo devices that require repairs,
please contact your Metabo service centre. You
can find the addresses on www.metabo.com.
2
).
Danger!
ENGLISH en
21