Cleaning, Maintenance And Ordering Of Spare Parts; Disposal And Recycling; Storage - EINHELL TE-CS 18 Li-Solo Originalbetriebsanleitung

Important. The hand-held circular saw must not
be operated with the saw blade key (13) inserted
in it.
•
Press the spindle lock (11).
•
Undo the screw to secure the saw blade (17)
using the saw blade key (13).
•
Push back and secure the moving swing
guard hood (19) using the lever for the swing
guard hood (20).
•
Remove the flange (18) and the saw blade
(12) in a downwards direction.
•
Clean the flange and insert the new saw bla-
de. Pay attention to the running direction (see
arrow on the guard hood and saw blade).
For 10 mm blade holder:
•
Place the flange (18) on the blade with the flat
side against the blade. (Make sure that the
flange is correctly positioned)
For 16 mm blade holder:
•
Place the flange (18) on the blade with the
raised side against the blade. (Make sure that
the flange is correctly positioned)
Warning! With the 16 mm holder, the fl ange must
center the blade. Therefore, pay special attention
to make sure that the raised part of the fl ange is
correctly positioned in the blade.
•
Tighten the screw to secure the saw blade
(17), check it runs true.
•
Before you press the On/Off switch, make
sure that the saw blade is correctly fitted and
that moving parts run smoothly and the clam-
ping screws are tightened securely.
6.5 LED lamp (Fig. 1/Item 5)
The LED lamp (5) can be used in poor lighting
conditions to additionally illuminate the cutting
position. The LED lamp (5) will come on automa-
tically as soon as you press the locking button for
the On/Off switch (3).
7. Cleaning, maintenance and
ordering of spare parts
Danger!
Always pull out the battery pack before starting
any cleaning work.
Anl_TE_CS_18_Li_solo_SPK7.indb 25 Anl_TE_CS_18_Li_solo_SPK7.indb 25
GB
7.1 Cleaning
•
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it with compressed air at low
pressure.
•
We recommend that you clean the device
immediately each time you have finished
using it.
•
Clean the equipment regularly with a moist
cloth and some soft soap. Do not use
cleaning agents or solvents; these could at-
tack the plastic parts of the equipment. Ensu-
re that no water can seep into the device. The
ingress of water into an electric tool increases
the risk of an electric shock.
7.2 Maintenance
There are no parts inside the equipment which
require additional maintenance.
7.3 Ordering replacement parts:
Please quote the following data when ordering
replacement parts:
•
Type of machine
•
Article number of the machine
•
Identification number of the machine
•
Replacement part number of the part required
For our latest prices and information please go to
www.isc-gmbh.info

8. Disposal and recycling

The equipment is supplied in packaging to pre-
vent it from being damaged in transit. The raw
materials in this packaging can be reused or
recycled. The equipment and its accessories are
made of various types of material, such as metal
and plastic. Never place defective equipment in
your household refuse. The equipment should
be taken to a suitable collection center for proper
disposal. If you do not know the whereabouts of
such a collection point, you should ask in your
local council offi ces.

9. Storage

Store the equipment and accessories in a dark
and dry place at above freezing temperature. The
ideal storage temperature is between 5 and 30
°C. Store the electric tool in its original packaging.
- 25 -
19.05.16 10:41 19.05.16 10:41