Technical Specification; Resetting To Factory Defaults - Phottix Mitros TTL Flash Benutzerhandbuch

Quick Flash Function
The Quick Flash function allows the flash to fire at 1/6 to 1/2 of the full output.
Quick Flash recycle times are faster. It helps for snap photography for near sub-
jects.
Quick flash can be used for continuous drive modes, quick flash for continuous
shot function can be enabled or disabled (see C.Fn-06 above).
Please note:
The Quick Flash Function makes flash firing a priority. Under-exposure could
result if the subject is located too far from the camera.
TTL Pref
TTL may vary slightly when using the flash on different cameras. TTL Pref (C.Fn-
15) setting allows users to adjust EV from +3 to -3 in 1/3rd stops to compensate
for these slight variations. This adjustment is a personal preference based on
camera standard TTL and will be stored in memory. When this EV level prefer-
ence is set, this compensation will be used for images taken in TTL mode. This EV
compensation will not be displayed on the LCD during regular use.
Slow Flash Sync
When both the subject and background are in a low-light environment, this fea-
ture can be useful to control the flash at slow shutter speeds further to achieve
the correct exposure.
The use of a tripod is strongly recommended in this mode when using slower
shutter speeds to prevent camera shake.

Resetting to Factory Defaults

The Phottix Mitros Flash can reset to factory defaults.
To reset the flash:
1. Press and hold the and
2. The flash will reset to factory default settings.
3. All custom functions will be reset to factory defaults.
Flash Information Display
For technical support or firmware upgrade checking the Phottix Mitros infor-
mation may be need. To display the hardware, software, icon library and serial
number display:
1. Press and hold the button and turn on the flash.
2. Press any button to cancel this display and enter the LCD screen.
Changes to the flash capacitor:
If the flash is not used for some time physical changes will take place within the
flash's capacitor. Make sure to turn on the flash a minimum of 10 minutes every
three months to prevent any physical changes.
12
buttons for 3 seconds.
INSTRUCTION MANUAL
En

Technical Specification

Modes: TTL, Manual, and Multi Stroboscopic
Guide No.: 58/190 (at 105mm focal length, ISO 100 in meters/feet)
Flash coverage: 24-105mm (14mm with wide angle diffuser panel)
Auto zoom (Flash coverage automatically adjusts to match the lens focal length)
Manual zoom (Zoom can be adjusted by changing setting on the flash/camera)
Rotation: 360 degrees, Up-Down: -7 to 90 degrees.
FEC (Flash exposure compensation): Manual
Sync modes: First Curtain Sync and High Speed Sync
Stroboscopic flash: 1-100HZ
Flash exposure confirmation: Blue LED lamp lights up in TTL mode
Flash Recycling (with size-AA alkaline batteries)
Recycling time/Flash-ready indicator:
Normal flash: Approx.0.1-5 sec./Red LED indicator lamp lights up.
Quick flash: Approx.0.1-2.5 sec./Green LED indicator lamp lights up.
Internal power: Four size-AA alkaline batteries or size-AA Ni-MH batteries
External battery: Compatible with Phottix Battery Pack and Sony compact bat-
tery pack FA-EB1AM through specific adapter
Power saving: Non-wireless Slave modes: 90 seconds, Wireless Slave mode: 60
minutes or 10 minutes
Wireless flash
Transmission method: Optical pulse
Channels: 4
Wireless options: Master and Slave
The Phottix Mitros Flash can be used as Wireless Master Unit only on some
cameras, they are: DSLR-A900, DSLR-A850, DSLR-A700, SLT-A99V/ SLT-A99, SLT-
A77V/ SLT-A77, SLT-A65V/ SLT-A65, SLT-A58, SLT-A57, SLT-A37, NEX-7or NEX-6.
Transmission range (Approx.): Indoors:12-16m/39.36-52.48 ft.
Outdoors: 7-9m/22.96-29.52 ft.
Reception angle: ±40°(horizontal), ±30°(vertical)
Controlled Slave groups: 2(A and B)
Flash ratio control: Each group can be set between- "-"(OFF), 1, 2, 4, 8 and 16
Standby current: ≤100uA in sleep mode
Dimensions: (L x W x H): 201x77.5x58.3mm
Weight: 416g (flash only, excluding batteries)
www.phottix.com