Inhaltsverzeichnis
Werbung
Allgemeiner Teil / General Section
Sound carriers ( )
T
Z
Use the
keys to select the desired frequency of the sound carriers for the left and
"
"
right channel.
Note:
16 sound carriers (3 stereo, 13 mono) are preset at the factory (they cannot be changed).
~
Deemphasis/noise suppression (
)
You have the choice between PANDA, 50µs (50US), and J17. Select the option giving the
best sound quality.
Favourite programme (
)
(
To quickly access your favourite programmes, these can be marked (
If no menu is displayed, you can use the
mode. In favourite mode, only the favourite programmes are availalbe for being selected
M
N
with the
" keys. The symbol »
« appears in front of the programme position number.
(
"
Note:
If you enter a programme position number directly with the numeric keys, the favourite
mode is automatically de-activated.
When switching the receiver on from stand-by, the favourite mode is also de-activated.
Contrast/video deviation ( )
Satellites transmit with different frequency deviations. This results in a corresponding con-
trast setting on the receiver.
The correct contrast level is preset at the factory.
If necessary or when programming a new channel, you can select between two factory-pre-
set contrast levels (1 and 2).
You should not change these preset values as this would also change the contrast setting of
all other programme positions.
In exceptional cases, you can change the contrast levels in the "System setup" menu (see
section "Presetting the contrast levels 1 and 2" on page 14).
Time ( ; e.g. summer/winter time)
Note:
If you wish to use the Timer function (Timer menu), the clock must correctly be set. You
should therfore check the time.
If a mains failure occurs, the clock stops running and is automatically cleared.
M
N
Use the
" keys to switch over between hours (0...23) and minutes (0...59) display.
"
T
Z
Use the
keys to change the selected value.
"
"
Selecting a programme position (
)
&
Note:
The currently used programme position is automatically preset.
T
Z
Use the numeric keys or the
keys to select the desired programme position num-
"
"
ber.
Entering the start and stop time (
M
N
Use the
" keys to toggle between start and stop time and hours (0...23) and minutes
"
(0...59) display.
Enter the value directly with the numeric keys or change a value with the
Note:
If a stop time is entered which lies before the start time, the Timer remains activated until
the stop time is reached next day
Saving or clearing a Timer ( )
T
Z
keys to switch the Timer on ( " " position).
Use the
"
"
Save the settings made by pressing the
Note:
If you wish to exit the Timer menu without saving, press the
Switch the receiver to stand-by if it is not used otherwise.
At the start time of the Timer the receiver must be in stand-by.
Note:
To signal that the Timer is programmed, the green indicator lights up in addition to the red
indicator.
If you wish to change an existing programmed Timer, call up the Timer menu again.
Note:
You can overwrite the current settings by entering new values, or clear the existing values
by exiting the Timer menu with the "
1 - 12
»
«
).
(
key to toggle between normal and favourite
"
,
)
T
Z
keys.
"
"
"
key. The Timer menu is automatically exited.
OK
key.
"
X
" setting.
Decoder setting (/)
According to the decoder used, one of four possible settings can be selected for each pro-
gramme position.
X–X
Decoder off
ü–X
Only the audio signal is decoded.
X–
=
Only the video signal is decoded.
–
Both the video and audio signals are decoded.
=
Video polarity (
)
=
Note:
You can select a positive ("+") or negative ("–") video polarity.
The "+" setting is preprogrammed. For certain decoders, the "–" setting is required.
9.5 The Timer menu/video recordings
Notes:
The Timer menu is provided for programming a 24-hour Timer for video recordings.
When a Timer is active, it is not possible to select another programme position or to display
on-screen menus. That is why the Timer of the receiver should be programmed for video
recordings at first (see also the section "During a Timer recording", page 20).
Overview
Press the
key and then the
key.
"
"
1
On the picture screen appear the status menu and then the Timer menu.
Check the time and correct it if necessary.
300
&
20:14
22:05
16:37
/ OK
Meaning of symbols:
300
Programme position number
&
20:14
Start time
22:05
Stop time
Timer on/off
16:37
Time
/ OK
:
exit menu without saving,
OK: save and exit menu.
Programming the video recorder
Do not forget to programme your video recorder to start and stop recording as well.
Note:
If your video recorder is provided with the VPS or Show-View programming facility, you can
use this. When programming the SAT Timer, make sure that it starts a little before and finis-
hes a little after the start and end times given in your TV programme guide, to ensure that
the entire programme is recorded even if the start time should be shifted.
During a Timer recording
Note:
During the Timer recording, the red indicator is lit and the green indicator is flashing.
When the Timer has elapsed, the receiver goes in stand-by mode again and only the red
indicator is lit.
The Timer is automatically set to "off". The programmed start and stop times remain stored
and maybe used everyday by activating the timer again (e.g. for a TV series).
To avoid the Timer recording from being disturbed, both the keys on the receiver and on the
remote control unit are locked during the programmed Timer period. This prevents an inad-
vertent change of the programmed settings. Only the b key on the remote control unit and
the
key on the receiver are not locked.
"
If you wish to abort a timer recording, use the
Switch the receiver on again, call up the Timer menu (press the
X
the Timer off ("
").
Direct reccording without Timer
Note:
If the video recorder obtains the signals via the VCR Euro-AV socket (AV programme posi-
tion on the video recorder), nothing will be displayed during recording. It is therefore possi-
ble to display the time or to call up the Timer menu (for example to check the stop time)
without affecting recording.
During direct recording, programme position change is not locked. That is why you should
principally use the Timer of the receiver to make video recordings.
STR 1300
key to switch the receiver to stand-by.
"
key twice) and switch
"
GRUNDIG Service
Werbung
Inhaltsverzeichnis
