Technical Data; Noise/Vibration Information; Battery Charging - Bosch AdvancedMulti 18 Originalbetriebsanleitung

OBJ_BUCH-2966-001.book Page 19 Wednesday, March 8, 2017 9:58 AM
6 Thumbwheel for orbit frequency preselection
7 Venting slots
8 Vibration-dampening auxiliary handle
(insulated gripping surface)*
9 Thread for auxiliary handle
10 Tool holder
11 180° light band
12 Plunge saw blade*
13 Sanding plate*
14 Sanding sheet*
15 Depth stop*
16 Segment saw blade*
17 Handle (insulated gripping surface)
18 Vacuum hose*
19 Vacuum connection*
20 Dust extraction*
21 Clamping lever of the dust extraction
*Accessories shown or described are not part of the standard de-
livery scope of the product. A complete overview of accessories
can be found in our accessories program.

Technical Data

Cordless Multifunction Tool
Article number
Preselection of
orbital stroke rate
Constant electronic control
Soft starting
AutoClic tool holder
Rated voltage
No-load speed n
0
Oscillation angle, left/right
Weight according to
EPTA-Procedure 01:2014
– without auxiliary handle
– with auxiliary handle
Permitted ambient
temperature
– during charging
– during operation* and
during storage
Recommended batteries
Recommended chargers
* limited performance at temperatures <0 °C
Technical data determined with battery from delivery scope.

Noise/Vibration Information

Sound emission values determined according to
EN 60745-2-4.
Typically the A-weighted noise levels of the product are:
Sound pressure level 82 dB(A); Sound power level 93 dB(A).
Uncertainty K =3 dB.
Wear hearing protection!
Bosch Power Tools
Working without auxiliary handle
Vibration total values a
determined according to EN 60745-2-4:
Sanding: a
Sawing with plunge cut saw blade: a
Sawing with segment saw blade: a
Working with auxiliary handle
Vibration total values a
determined according to EN 60745-2-4:
Sanding: a
Sawing with plunge cut saw blade: a
Sawing with segment saw blade: a
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with anoth-
er. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main
applications of the tool. However if the tool is used for differ-
ent applications, with different accessories or insertion tools
or is poorly maintained, the vibration emission may differ.
This may significantly increase the exposure level over the
total working period.
An estimation of the level of exposure to vibration should al-
AdvancedMulti 18
so take into account the times when the tool is switched off
3 603 A04 0..
or when it is running but not actually doing the job. This may
significantly reduce the exposure level over the total working

period.
 Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and

the accessories, keep the hands warm, organisation of work

patterns.
V= 18
–1
min 10000–20000
Assembly
° 2.8

Battery Charging

 Use only the battery chargers listed on the accessories
kg 1.5
kg 1.6
Note: The battery supplied is partially charged. To ensure full
capacity of the battery, completely charge the battery in the
°C 0...+45
battery charger before using your power tool for the first time.
The lithium-ion battery can be charged at any time without re-
°C –20...+50
ducing its service life. Interrupting the charging procedure
PBA 18V....V-.
does not damage the battery.
PBA 18V....W-.
The lithium-ion battery is protected against deep discharging
AL 18.. CV
by the "Electronic Cell Protection (ECP)". When the battery is
empty, the machine is switched off by means of a protective
circuit: The inserted tool no longer rotates.
Note: If the machine should automatically switch off because
of a discharged or overheated battery, make sure to set the
machine's On/Off switch 2 to off. Charge the battery and al-
low it to cool down before restarting the machine. Otherwise
the battery can become damaged.
(triax vector sum) and uncertainty K
h
2 2
=6 m/s , K=1.5 m/s ,
h
h
=14 m/s
h
(triax vector sum) and uncertainty K
h
2 2
=6 m/s , K=1.5 m/s ,
h
h
=16 m/s
h
page. Only these battery chargers are matched to the lith-
ium-ion battery of your power tool.
English | 19
2 2
=16 m/s , K=1.5 m/s ,
2 2
, K=1.5 m/s .
2 2
=20 m/s , K=2.5 m/s ,
2 2
, K=1.5 m/s .
1 609 92A 3B0 | (8.3.17)