Technical Data; Noise/Vibration Information - Bosch GSH 5 CE Professional Originalbetriebsanleitung

OBJ_BUCH-419-009.book Page 12 Monday, December 9, 2013 2:43 PM
12 | English
Product Features
The numbering of the product features refers to the illustra-
tion of the machine on the graphics page.
1 Dust protection cap
2 Locking sleeve
3 Chisel adjustment ring (Vario-Lock)
4 Vibration damper
5 Handle (insulated gripping surface)
6 On/Off switch
7 Thumbwheel for preselection of impact rate
8 Service indicator
9 Stand-by indicator
10 Auxiliary handle (insulated gripping surface)
11 Knurled nut for auxiliary handle
Accessories shown or described are not part of the standard deliv-
ery scope of the product. A complete overview of accessories can
be found in our accessories program.

Technical Data

Demolition Hammer
Article number
Rated power input
Impact rate
Impact energy per
stroke according to
EPTA-Procedure 05/2009
Chisel positions
Tool holder
Lubrication
Weight according to
EPTA-Procedure 01/2003
Protection class
The values given are valid for a nominal voltage [U] of 230 V. For differ-
ent voltages and models for specific countries, these values can vary.

Noise/Vibration Information

Measured sound values determined according to EN 60745.
Typically the A-weighted noise levels of the product are:
Sound pressure level 86 dB(A); sound power level 98 dB(A).
Uncertainty K=3 dB.
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 60745:
2
Chiselling: a = 11 m/s , K= 1.5 m/s
h
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with anoth-
er. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or insertion tools or is
poorly maintained, the vibration emission may differ. This
may significantly increase the exposure level over the total
working period.
1 609 92A 0FE | (9.12.13)
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working
period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
terns.
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with the fol-
lowing standards or standardization documents: EN 60745
according to the provisions of the directives 2011/65/EU,
2004/108/EC, 2006/42/EC, 2000/14/EC.
2000/14/EC: Guaranteed sound power level 105 dB(A).
Conformity assessment procedure according to Annex VI.
Equipment category: 10
Notified body:
TÜV NORD CERT GmbH & Co. KG,
GSH 5 CE Am TÜV 1, 30519 Hannover
Technical file (2006/42/EC) at:
3 611 C21 0..
Robert Bosch GmbH, PT/ETM9,
W 1150
D-70745 Leinfelden-Echterdingen
-1
min 1300– 2900
Henk Becker
Executive Vice President
Engineering
J 8,3
12
SDS-max
Central permanent
Robert Bosch GmbH, Power Tools Division
lubrication
D-70745 Leinfelden-Echterdingen
Leinfelden, 10.12.2013
kg 6.2
Assembly
/II
 Before any work on the machine itself, pull the mains
Auxiliary Handle (see figure A)
 Operate your machine only with the auxiliary handle
The auxiliary handle 10 can be set to any position for a secure
and low-fatigue working posture.
– Loosen the knurled nut 11, rotate the auxiliary handle 10
2
.
– The auxiliary handle 10 can be mounted to a different posi-
Helmut Heinzelmann
Head of Product Certification
PT/ETM9
plug.
10.
around the axis of the machine to the required position and
tighten the knurled nut 11 again.
tion. For this, completely unscrew the knurled nut 11 and
then pull out the hexagon bolt upward. Pull off the auxiliary
handle 10 to the side and turn around the remaining
clamping element by 180°. Mount the auxiliary handle 10
in reverse order.
Bosch Power Tools