Important Safety Instructions - Canon i-SENSYS LBP710Cx Erste Schritte

Important Safety Instructions

This manual describes only warnings and cautions
for the installation and the power supply. Be sure
to read "Important Safety Instructions" described in
the e-Manual (HTML manual) also.
WARNING
Indicates a warning concerning operations
that may lead to death or injury to persons if
not performed correctly. To use the machine
safely, always pay attention to these warnings.
CAUTION
Indicates a caution concerning operations
that may lead to injury to persons if not
performed correctly. To use the machine
safely, always pay attention to these cautions.
Installation
WARNING
Do not install in a location that may result in a
fire or electrical shock
A location where the ventilation slots are
•
blocked (too close to walls, beds, sofas, rugs, or
En
similar objects)
• A damp or dusty location
• A location exposed to direct sunlight or outdoors
• A location subject to high temperatures
A location exposed to open flames
•
Near alcohol, paint thinners or other
•
flammable substances
Other warnings
Do not connect unapproved cables to this
•
machine. Doing so may result in a fire or
electrical shock.
• Do not place necklaces and other metal
objects or containers filled with liquid on the
machine. If foreign substances come in contact
with electrical parts inside the machine, it may
result in a fire or electrical shock.
If any foreign substance falls into this machine,
•
unplug the power plug from the AC power outlet
and contact your local authorized Canon dealer.
CAUTION
Do not install in the following locations
The machine may drop or fall, resulting in injury.
An unstable location
•
A location exposed to vibrations
•
Other cautions
When carrying this machine, follow the
•
instructions in this manual. If carried
improperly, it may fall, resulting in injury.
• When installing this machine, be careful not to
get your hands caught between the machine and
the floor or walls. Doing so may result in injury.
Avoid poorly ventilated locations
This machine generates a slight amount of ozone
and other emissions during normal use. These
emissions are not harmful to health. However,
they may be noticeable during extended use or
long production runs in poorly ventilated rooms.
To maintain a comfortable working environment,
it is recommended that the room where the
machine operates be appropriately ventilated.
Also avoid locations where people would be
exposed to emissions from the machine.
Power Supply
WARNING
Use only a power supply that meets the
•
specified voltage requirements. Failure to do
so may result in a fire or electrical shock.
• Do not use power cords other than the one provided,
as this may result in a fire or electrical shock.
• The provided power cord is intended for use
with this machine. Do not connect the power
cord to other devices.
Do not modify, pull, forcibly bend, or perform
•
any other act that may damage the power
cord. Do not place heavy objects on the power
cord. Damaging the power cord may result in
a fire or electrical shock.
• Do not plug in or unplug the power plug with
wet hands, as this may result in an electrical shock.
• Do not use extension cords or multi-plug
power strips with the machine. Doing so may
result in a fire or electrical shock.
Do not wrap the power cord or tie it in a knot,
•
as this may result in a fire or electrical shock.
Insert the power plug completely into the AC
•
power outlet. Failure to do so may result in a
fire or electrical shock.
14
Remove the power plug completely from the
•
AC power outlet during a thunder storm.
Failure to do so may result in a fire, electrical
shock, or damage to the machine.
CAUTION
Install this machine near the power outlet and
leave sufficient space around the power plug so
that it can be unplugged easily in an emergency.
Handling
Laser Safety
This product is confirmed as a Class 1 laser
product in IEC60825-1:2007 and EN60825-1:2007.
CLASS 1 LASER PRODUCT
LASER KLASSE 1
APPAREIL À LASER DE CLASSE 1
APPARECCHIO LASER DI CLASSE 1
PRODUCTO LÁSER DE CLASE 1
APARELHO A LASER DE CLASSE 1
LUOKAN 1 LASER-TUOTE
LASERPRODUKT KLASS 1
The laser beam can be harmful to human bodies.
Since radiation emitted inside the product is
completely confined within protective housings
and external covers, the laser beam cannot
escape from the machine during any phase of
user operation. Read the following remarks and
instructions for safety.
• Never open covers other than those instructed
in the manuals for this machine.
• If the laser beam should escape and enter your
eyes, exposure may cause damage to your eyes.
CAUTION
Use of controls, adjustments, or performance of
procedures other than those specified in this
manual may result in hazardous radiation exposure.
Safety-Related Symbols
Power switch: "ON" position
Power switch: "OFF" position
Power switch: "STAND‐BY" position
Push‐push switch "ON"
Protective earthing terminal
Dangerous voltage inside. Do not open
covers other than instructed.
CAUTION: Hot surface. Do not touch.
Class II equipment
Moving parts: Keep body parts away from
moving parts
[NOTE]
Some of symbols shown above may not be
affixed depending on the product.
v1511_02_en-GB
Laser Safety Label
Consumables
WARNING
Do not dispose of used toner cartridges or the like
in open flames. Also, do not store toner cartridges
or paper in a location exposed to open flames.
This may cause the toner to ignite, and result in
burns or fire.
Notice
Product Name
Safety regulations require the product's name to
be registered.
In some regions where this product is sold, the
following name(s) in parentheses ( ) may be
registered instead.
LBP712Cx/LBP710Cx (F169200)
EMC requirements of EC Directive
This equipment conforms with the essential EMC
requirements of EC Directive. We declare that
this product conforms with the EMC
requirements of EC Directive at nominal mains
input 230 V, 50 Hz although the rated input of
the product is 220 to 240 V, 50/60 Hz. Use of
shielded cable is necessary to comply with the
technical EMC requirements of EC Directive.
WEEE and Battery Directives
You can see the WEEE and Battery Directives
information in the latest e-Manual (HTML
manual) from the Canon website (http://canon.
com/oip-manual).
Trademarks
Mac is a trademark of Apple Inc.
Microsoft, Windows, Windows Vista, Windows
Server, Internet Explorer, Excel, and PowerPoint
are either registered trademarks or trademarks of
Microsoft Corporation in the United States and/
or other countries.
Other product and company names herein may
be the trademarks of their respective owners.
Third-Party Services
If you use third-party services through the
PRODUCT, use of the services are subjected the
conditions below.
When you access and/or obtain some third party
content (such as text, images, videos, audios, or
software) through the SOFTWARE, except as
expressly permitted by the content owner or by
applicable law, you may not (a) scrape, build
databases or otherwise create permanent copies
of such content, or keep cached copies longer
than permitted by the cache header; (b) copy,
translate, modify, create a derivative work of, sell,
lease, lend, convey, distribute, publicly display or
sublicense to any third party; (c) misrepresent
the source or ownership; and (d) remove,
obscure, or alter any copyright, trademark or
other proprietary rights notices, falsify or delete
any author attributions, legal notices or other
labels of the origin or source of material.
Third Party Software
This Canon product (the "PRODUCT") product
includes third-party software modules. Use and
distribution of these software modules,
including any updates of such software modules
(collectively, the "SOFTWARE") are subject to
license conditions (1) through (9) below.
(1) You agree that you will comply with any
"OFF"
applicable export control laws, restrictions or
regulations of the countries involved in the
event that this PRODUCT including the
SOFTWARE is shipped, transferred or
exported into any country.
(2) Rights holders of the SOFTWARE retain in all
respects the title, ownership and intellectual
property rights in and to the SOFTWARE.
Except as expressly provided herein, no
license or right, expressed or implied, is
hereby conveyed or granted by rights holders
of the SOFTWARE to you for any intellectual
property of rights holders of the SOFTWARE.
(3) You may use the SOFTWARE solely for use
with the PRODUCT.
(4) You may not assign, sublicense, market,
distribute, or transfer the SOFTWARE to any
third party without prior written consent of
rights holders of the SOFTWARE.
(5) Notwithstanding the foregoing, you may
transfer the SOFTWARE only when (a) you
assign all of your rights to the PRODUCT and all
rights and obligations under the license
conditions to transferee and (b) such transferee
agrees to be bound by all these conditions.
(6) You may not decompile, reverse engineer,
disassemble or otherwise reduce the code of
the SOFTWARE to human readable form.
(7) You may not modify, adapt, translate, rent,
lease or loan the SOFTWARE or create
derivative works based on the SOFTWARE.
(8) You are not entitled to remove or make
separate copies of the SOFTWARE from the
PRODUCT.
(9) The human-readable portion (the source
code) of the SOFTWARE is not licensed to you.
Notwithstanding (1) through (9) above, the
PRODUCT includes third-party software modules
accompanying the other license conditions, and
these software modules are subject to the other
license conditions.
Please refer to the other license conditions of
third-party software modules described in
Appendix of Manual for the corresponding the
PRODUCT. This Manual is available at
http://canon.com/oip-manual.
By using the PRODUCT, you shall be deemed to
have agreed to all applicable license conditions.
If you do not agree to these license conditions,
please contact your service representative.