GRAPHITE 59G087 Übersetzung Der Originalanleitung Seite 10

you hold the sander with both hands while working (also using the
auxiliary handle), there is less risk of your hand touching the rotating
disc or brush and being injured by kickback.
INSTALLATION AND ADJUSTMENT OF THE SHIELD
The blade guard protects the operator from splinters, accidental contact
with the work tool or sparks. It should always be fitted with extra attention
paid to ensuring that its covering part faces the
the blade guard attachment allows the guard to be set in the optimum
position without tools.
• Loosen and pull back the lever (7) on the disc guard (4).
• Rotate the disc guard (4) to the desired position.
• Lock by lowering the lever (7).
Removing and adjusting the disc guard is done in the reverse order to
its installation.
TOOL REPLACEMENT
Work gloves must be worn during tool changing operations.
The spindle lock button (1) is only to be used to lock the spindle
of the grinder when mounting or dismounting the work tool. It
must not be used as a brake button while the disc is spinning.
Doing so may damage the grinder or injure the user.
DISC MOUNTING
For grinding or cutting discs with a thickness of less than 3 mm,
the nut of the outer flange (5) should be screwed on flat on the
disc side.
- Press the spindle lock button (1).
• Insert the special key (8) (supplied) into the holes of the outer
flange (5).
• Turn key - loosen (8) and remove outer flange (5).
• Place the disc so that it is pressed against the surface of the inner
flange (6).
• Screw on outer flange (5) and lightly tighten with special spanner
(8).
Dismantling of the discs is carried out in the reverse order to assembly.
During assembly, the disc should be pressed against the surface of the
inner flange (6) and centrally seated on its underside.
FITTING WORKING TOOLS WITH THREADED HOLE
• Press the spindle lock button (1).
• Remove the previously mounted implement - if fitted.
• Remove both flanges - inner flange (6) and outer flange (5) - before
installation.
• Screw the threaded part of the working tool onto the spindle and
tighten slightly.
Disassembly of threaded hole work tools is in reverse order to
assembly.
MOUNTING OF ANGLE GRINDER IN ANGLE GRINDER STAND
It is permissible to use the angle grinder in a dedicated tripod for angle
grinders, provided it is fitted correctly in accordance with the tripod
manufacturer's assembly instructions.
OPERATION / SETTINGS
Check the condition of the grinding wheel before using it. Do not
use chipped, cracked or otherwise damaged grinding wheels. A
worn wheel or brush should be replaced immediately with a new
one before use. When you have finished working, always switch
off the grinder and wait until the working tool has come to a
complete standstill. Only then can the sander be put away. Do not
brake the rotating grinding wheel by pressing it against the
workpiece.
Never overload the grinder. The weight of the power tool exerts
sufficient pressure to operate the tool effectively. Overloading and
excessive pressure can cause the power tool to break
dangerously.
• If the sander falls during operation, it is essential to inspect
and, if necessary, replace the working tool if it is found to be
damaged or deformed.
• Never strike the work tool against the work material.
• Avoid bouncing and scraping with the disc, especially when
working on corners, sharp edges, etc. (this can cause loss of
control and kickback). (this may result in loss of control of the
power tool and a kickback effect).
• Never use saw blades designed for cutting wood from circular
saws. The use of such saw blades often results in a recoil
phenomenon of the power tool, loss of control and can lead to
injury to the operator.
ON/OFF
operator.The design of
10
Hold the sander with both hands during start-up and operation.
• Press the rear part of the switch (2).
• Slide the switch (2) forward - (towards the head).
• For continuous operation - press the front of the switch button.
• The switch will automatically be locked in the continuous running
position.
• To switch off the unit - press the back of the switch button (2).
After starting the grinder, wait until the grinding wheel has reached
maximum speed before starting work. The switch must not be
operated while the sander is switched on or off. The sander switch
must only be operated when the power tool is away from the
workpiece.
The appliance has a fuse-protected switch, which means that if
there is a temporary mains power failure or it is plugged into a
power socket with the switch in the "on" position, it will not start.
In this case, the switch must be reversed to the 'off' position and
the unit restarted. CUTTING
• Cutting with an angle grinder can only be done in a straight
line.
• Do not cut the material while holding it in your hand.
• Large workpieces should be supported and care should be
taken that the support points are close to the cutting line and
at the end of the material. Material placed stably will not tend to
move during cutting.
• Small workpieces should be clamped e.g. in a vice, using
clamps, etc. The material should be clamped so that the
cutting point is close to the clamping element. This will ensure
greater cutting precision.
• Do not allow vibration or tamping of the cutting disc, as this
will impair the quality of the cut and may cause the cutting disc
to break.
• No lateral pressure should be exerted on the cutting disc
during cutting.
• Use the correct cutting disc depending on the material to be
cut.
• When cutting through material, it is recommended that the
direction of feed is in line with the direction of rotation of the
cutting disc.
The depth of cut depends on the diameter of the disc.
• Only discs with nominal diameters no larger than those
recommended for the grinder model should be used.
• When making deep cuts (e.g. profiles, building blocks, bricks, etc.),
do not allow the clamping flanges to come into contact with the
workpiece.
Cutting discs reach very high temperatures during operation - do
not touch them with unprotected parts of the body before they
have cooled down.
SANDING
Grinding work can be carried out using e.g. grinding discs, cup wheels,
flap discs, discs with abrasive fleece, wire brushes, flexible discs for
sandpaper, etc. Each type of disc and workpiece requires a suitable
working technique and the use of appropriate personal protective
equipment. Discs designed for cutting should not be used for
sanding. Grinding discs are designed to remove material with the
edge of the disc.
• Do not grind with the side face of the disc. The optimum
working angle for this type of disc is 30
• Grinding work must only be carried out using grinding discs
suitable for the material.
When working with flap discs, abrasive fleece discs and flexible
discs for sandpaper, care must be taken to ensure the correct
angle of attack.
- Do not sand with the entire surface of the disc.
- These types of discs are used for machining flat surfaces.
Wire brushes are mainly intended for cleaning profiles and hard-
to-reach areas. They can be used to remove, for example, rust,
paint coatings, etc. from material surfaces.
Only work tools whose permissible speed is higher than or equal
to the maximum speed of the angle grinder without load should be
used.
OPERATION AND MAINTENANCE
Unplug the power cord from the mains socket before carrying out
any installation, adjustment, repair or operation.
MAINTENANCE AND STORAGE
o .