Weller WXR 3 Originalbetriebsanleitung Seite 24

Parameter menu
Pressure gauge threshold
TСТs ПunМtТon Мan bО usОН to НОinО tСО maТntО-
nance interval of the desoldering tool. This is done
bв sОttТnР tСО vaХuО Тn mbar at wСТМС tСО ОХОМtrТМ
pressure gauge issues a warning signal when the
ТntaФО sвstОm Тs МontamТnatОН (δϋϊ oП tСО vaМuum
pump swТtМСОs Пrom РrООn to rОН)έ TСО sОt vaХuО Тs
dependent on the suction nozzles used.
Adjustable
ПaМtorв sОttТnР
1. TСО sвstОm (tТps anН iХtОr) must bО ПrООέ
Interface COM 1 / 2
Option Description
SОrТaХ МommunТМatТon wТtС Pω or otСОr МompatТbХО WОХХОr НОvТМОs (ПaМtorв sОttТnР)έ
RS232
TСО ωτε 1 port Тs МoniРurОН as a Пoot swТtМС Тnput Пor aМtТvatТnР tСО aТr lowέ
Air
TСО ωτε 1 port Тs МoniРurОН as a Пoot swТtМС Тnput Пor aМtТvatТnР tСО vaМuumέ
Vac
TСО ωτε 1 port Тs МoniРurОН as a Пoot swТtМС Тnput Пor aМtТvatТnР tСО PТМФUp vaМuumέ
PickUp
StopΤύo
The COM 1 port is used to drive an optional optotransmitter so that a KHE-P control
unТt Мan bО aМtТvatОН vТa an optТМaХ ibrОέ
TСО output Тs aМtТvatОН wСОn a tooХ Тs usОНέ In aННТtТon, tСО loatТnР swТtМСОН output Тs
МХosОНέ TСО output Тs oПП Тn tСО StanНbв, χuto τПП or τПП posТtТons, or ТП no tooХ Тs ТnsОrtОНέ
Floating switching output 1
Floating switching output 1 is located at the COM 1 port.
Option Description
(ПaМtorв sОttТnР)
OFF
TСО loatТnР swТtМСТnР output Тs МХosОН wСОn a tooХ Тs Тn usОέ SОХОМtОН ГОro SmoР
ZeroSmog
ОxtraМtТon sвstОms Мan bО МonnОМtОН usТnР an optТonaХ aНaptor (WX ώUψ)έ TСО rОar
RS 232 port remains functional.
SwТtМСТnР output Тs opОn Тn tСО StanНbв, χuto τПП or τПП posТtТons, or ТП no tooХ Тs ТnsОr-
ted.
42
www.valuetronics.com
-400 mbar to -800 mbar
άθίί mbar
Notice
If the Cτε 1 port is also conigured for „StopΤGo" use, the „Filter full"
message is evaluated by the WX HUB and, where applicable, a
message appears on the display .
Menu access
2. SОХОМt tСО mОnu ТtОm „PrОssurО РauРО
threshold" in the menu.
3. SОt tСО „PrОssurО РauРО tСrОsСoХН" prОssurО
vaХuО wТtС tСО UP or ϊτWσ buttonέ TСО status
LED switches back and forth between red and
green. Use the UP button to increase vacuum
bв ηί to κί mbar, tСОn pТnМС tСО vaМuum tubО
and check whether the LED switches from
green to red.
4. Adopting the set change.
Menu access
Menu access
Station parameters
Station parameters
Station parameters