CMi C-SWS-105 C Originalbetriebsanleitung Seite 17

– When it is cold, make sure your body and your
hands, in particular, are kept warm.
– Take regular breaks and move your hands at the
same time to promote circulation.
Electrical safety
• The device may only be connected to a socket
that is correctly installed and grounded.
• The fuse must be a residual current circuit-
breaker with a measured residual current of no
more than 30 mA.
• Make sure that the power supply corresponds
with the connection specifications of the device
before it is connected.
• The device may only be used within the specified
limitations for voltage and power (see type plate).
• Do not touch the mains plug with wet hands!
Always pull out the mains plug at the plug and not
by the cable.
• Do not bend, crush, pull or drive over the power
cable, protect from sharp edges, oil and heat.
• Do not lift the device using the cable or use the
cable for purposes other than intended.
• Check the plug and cable before each use.
• If the power cable is damaged immediately dis-
connect the plug. Never use the device if the
power cable is damaged.
• If the device is not in use make sure the plug is
pulled out.
• Make sure that the device is switched off before
plugging in the mains cable.
• Make sure that the device is switched off before
unplugging it.
• Disconnect the power supply before transporting
the device.
Dust extraction
Dusts from materials such as lead-containing paint,
some types of wood, minerals and metal may be
harmful to health. Touching of inhaling the dusts can
cause allergic reactions and/or ailments of the res-
piratory tract of the user or persons in the vicinity.
Certain dusts such as oak or beech dust are consid-
ered carcinogenic, particularly in combination with
wood treatment additives (chromate, wood preserva-
tives). Materials containing asbestos may only be
processed by experts.
– Always use a dust extraction facility.
– Make sure the workplace is well ventilated.
– Always wear a dust protection mask.
– Observe the regulations valid in your country for
the materials to be processed.
Device-specific safety instructions
• The tool may only be used for dry sanding.
• When operating the device ensure that the area
you are working in is clean and tidy.
• Do not leave objects or cable laying around in the
vicinity of the device.
• When working with the device make sure the area
is well lit.
• Secure the work piece to be processed to prevent
it from slipping.
• Prevent overheating of the device and the work
piece.
• Do not process any materials that contain hazard-
ous substances. There is a risk of cancerous sub-
stances being released!
• Keep the handles dry and free of grease.
• Symbols appearing on your device may not be
removed or covered. Signs on the device that are
no longer legible must be replaced immediately.
Read and observe the instructions for use
before using the product for the first time.
Personal protective equipment
Wear a dust mask when working in a dusty
environment.
Wear safety goggles while working with
sanding devices.
Wear hearing protection.
Dust extraction
Dusts from materials such as lead-containing paint,
some types of wood, minerals and metal may be
harmful to health. Touching of inhaling the dusts can
cause allergic reactions and/or ailments of the res-
piratory tract of the user or persons in the vicinity.
Certain dusts such as oak or beech dust are consid-
ered carcinogenic, particularly in combination with
wood treatment additives (chromate, wood preserva-
tives). Materials containing asbestos may only be
processed by experts.
– Always use a dust extraction facility.
– Make sure the workplace is well ventilated.
– Always wear a dust protection mask.
– Observe the regulations valid in your country for
the materials to be processed.
Your product at a glance
Note: The actual appearance of your prod-
uct may differ from the illustrations.
► P. 3, fig. 1
1. On-Off switch
2. Connecting pieces
3. Sanding plate
Scope of supply
• Multi sander
• Sanding disc
• Adapter for dust extraction
• Instructions for use
Using for the first time
Attach the sanding disc
The fixture of the sanding disc takes place by means
of hook and loop adhesion.
– Carefully align the sanding disc and press it firmly
onto the sanding plate.
– Press the device with the sanding sheet firmly
onto an even surface and switch on briefly.
GB
17