Cleaning And Maintenance; Environmental Protection - Evolution R255Sms-Db-Li Originalbetriebsanleitung

gradually and freely move to the open position. It should
close automatically when raising the cutting head.
• Do not release the cutting handle when the cutting head
of the saw is in the lower position. This will result in an
unstable rapid movement of the cutting head.
• When performing a mitre, bevel or compound cut, adjust
the sliding fences to ensure the correct clearance of the
blade.
RESIDUAL RISKS
Even with application of safety standards and using the tool
as prescribed, certain residual risks can remain:
• Risk of personal injury due to prolonged use.
• Risk of injury caused by dust.
• Risk of injury caused by flying objects.
• Risk of burns due to accessories becoming hot.

CLEANING AND MAINTENANCE

WARNING: Disconnect the battery packs from the tool
before any adjustments, cleaning, or maintenance is carried
out.
• Use compressed air to blow dirt out of the main housing
air vents and the blade guard.Wear approved eye
protection and a dust mask.
• Use a cloth dampened with water to clean the other
areas of the tool. Never use solvent based or harsh
chemicals of any type as this may weaken, damage or
destroy plastic components.
• Do not attempt to modify the tool or accessories in any
way.
• When servicing only use Evolution original parts and
carried out by a qualified person.

ENVIRONMENTAL PROTECTION

Waste electrical products should not be
disposed of with household waste.
Please recycle where facilities exist.
Check with your Local Authority or
retailer for recycling advice.
PRODUCT OVERVIEW KEY
1. Front handle
2. Upper blade guard
3. Blade rotation arrow
4. Rear carry handle
5. Depth stop screw
6. Lower blade guard
7. Cutting head rails
8. Bevel scale
9. Dust skirt
10. Sliding fence x2
11. Bevel index pin
12. Kerf plate
13. Front clamp sockets x2
14. Dual hex key
15. Rotary table
16. Mitre scale
17. Mounting holes x4
18. Mitre index override
19. On/off trigger
20. Trigger lock
21. Batteries*
22. Blade lock
23. Cutting head
24. Cutting head lock pin
25. Dust extraction port
26. Mitre index push button
27. Mitre lock
28. Carriage slides lock
29. Top clamp socket
30. Bevel lock
31. M6 X 16mm table extension screws
32. Outer blade flange
33. Inner blade flange
34. Dust extraction adaptor
35. M6 X 12mm rail securing cap screws
36. Dust bag
37. Blade
38. Mitre lock knob (pre-assembly)
39. Table extensions
40. Top clamp
41. Front clamp
42. Zero-clearance kerf plate
43. Battery charger*
*purchased separately
USING THE PRODUCT
Getting Started
• Assembly (Figs. 1..)
• Raising/lowering the cutting head (Figs. 2..)
• Blade assembly (Figs. 3..)
• Carrying the saw (Fig. 4)
• Optional dust extraction accessories (Fig. 5)
• Mounting the saw (Fig. 6)
• Using the clamps (Fig. 7)
• Supporting the workpiece (Fig. 8)
• Fitting the batteries (Fig. 9)
Operation
• Adjusting the depth (Figs. 10..)
• Maximum vertical cutting (Fig. 11)
• Mitre cutting (Figs. 12..)
• Bevel cutting (Figs. 13..)
Maintenance
• 0 Bevel stop adjustment (Figs. 14..)
• 45 Bevel stop adjustment (Figs. 15..)
• Machine fence alignment (Figs. 16..)
• Bevel pointer alignment (Figs. 17..)
• Mitre pointer alignment (Figs. 18..)
• Changing the dust skirt (Figs. 19..)
• Installing the zero clearance kerf plate (Figs.20..)
BATTERY STORAGE
If you intend to store a battery for a period without use
then store battery at room temperature (0°C to 20°C) When
storing for very long periods boost charge the battery
once per year to prevent over discharge. The Ambient
temperature range for tool and battery use: 0°C to 40°C. The
charging temperature: 5°C to 40°C.
NOISE WARNING
WARNING: The noise emissions during actual use
of the power tool can differ from the declared values
depending on the ways in which the tool is used
especially what kind of workpiece is processed.
EN