Werbung
Verfügbare Sprachen
Verfügbare Sprachen
This allows you to identify problem areas immediately
before first use and correct them if necessary.
The same procedure is recommended for critical
places, such as embankments/ditches/beds, etc.
Proceed as described above and start the mower
(see point 9) with the "START" button.
In the event of a problem, you can stop the mower by
pressing the stop button (4) on the product.
9. Starting up / adjustments
m ATTENTION!
To ensure optimum function, a software update
must be carried out before first use. (see 13.2
Software update)
m NOTE
For a long service life, the robotic lawnmower (1)
should only be operated at an outdoor temperature
of 5 - 40 °C.
m ATTENTION!
Always make sure the product is fully assembled
before commissioning!
Electrical connection
The electrical motor installed is connected and ready
for operation. The connection complies with the appli-
cable VDE and DIN provisions.
The customer's mains connection as well as the ex-
tension cable used must also comply with these reg-
ulations.
Damaged electrical connection cable
The insulation on electrical connection cables is often
damaged.
This may have the following causes:
• Pressure points, where connection cables are
passed through windows or doors.
• Kinks where the connection cable has been improp-
erly fastened or routed.
• Places where the connection cables have been cut
due to being driven over.
• Insulation damage due to being ripped out of the
wall outlet.
• Cracks due to the insulation ageing.
Such damaged electrical connection cables must not
be used and are life-threatening due to the insulation
damage.
Check the electrical connection cables for damage
regularly. Ensure that the connection cables are dis-
connected from electrical power when checking for
damage.
Electrical connection cables must comply with the ap-
plicable VDE and DIN provisions.
Only use connection cables of the same designation.
The printing of the type designation on the connection
cable is mandatory.
9.1. Quick start (Fig. 19/20)
After installing the boundary wire (11), you can use the
robotic lawnmower (1).
Adjusting the cutting height
• Turn the cutting height adjustment knob (2) clock-
wise to increase the cutting height seamlessly be-
tween 20 - 60 mm.
• Turn the cutting height adjustment knob (2) an-
ti-clockwise to decrease the cutting height seam-
lessly between 20 - 60 mm.
m NOTE
The arrow on the cutting height adjustment knob (2)
points to numbers outside the knob. Here you can
read off the cutting height currently set in 5 mm steps.
Halting/stopping the robotic lawnmower:
• To stop the robotic lawnmower, press the stop but-
ton (4).
• The robotic lawnmower stops immediately and the
blade disc (6) stops.
m ATTENTION
The robotic lawnmower is not switched off, it has only
been stopped. Always use the "POWER ON/OFF"
button to switch the robotic lawnmower off.
Switching the robotic lawnmower on:
• The robotic lawnmower can then be restarted as
described below.
m NOTE
Before the robotic lawnmower (1) starts mowing, an
acoustic signal (four beeps) is heard, then the blade
disc (6) starts rotating.
• Press the
til the robotic lawnmower (1) switches on.
• For the first use, enter the default PIN code "0000"
by pressing "OK" four times when the number "0"
flashes. (The PIN code can be changed as de-
scribed in point 9.2.1).
• After confirming the fourth digit with the "OK but-
ton", the robotic lawnmower is ready for use. The
word "IdLE" appears on the display.
m NOTE
The robotic lawnmower (1) switches off automatically
after 30 seconds if no input is made.
www.scheppach.com
-button ("POWER ON/OFF" button) un-
GB | 29
Werbung
