SIOUX 5979A Betriebsanweisung

Sioux
Operator Instructions
Includes—ForeseenUse,Work Stations,Putting Into Service,
Operating,Dismantling,AssemblyandSafetyRules.
Manufacturer/Supplier
Sioux Tools, Inc.
250 Snap-on Drive
P.O. Box 1596
Murphy, NC 28906
U.S.A.
Tel No. 828-835-9765
Fax No. 828-835-9685
Product Net Weight
Recommended
0.44 lbs
0.20 Kg
Air Pressure
RecommendedWorking
6.2
Maximum
6.2
SAFETY MESSAGES
Personal Safety Equipment
use —Safety Glasses YES
Use —Safety Gloves
Use —Safety Boots
Use —Breathing Masks YES
Use - Ear Protectors YES
Safety rules when using 5979A
Pencil Die Grinder
—Use accessories rated at least 70,000 RPM.
— Prolongedexposure to vibrationmay_cause i njury.
—Readall instructions before using this tool. All
operators must be fully trained in its use and aware of
these safety rules.
— Do not exceedthe maximum workingair pressure.
—Use personalprotection equipmentas recommended.
— Somedustcreatedbypowersanding, s awing, g rinding,
drilling, and other construction activities contains
chemicals knownto cause cancer, birth defects and other
reproductive harm.
—Use only compressed air at the recommended
conditions.
—If the tool appears to malfunction, remove from use
immediately and arrange for service
and repair. If it is not practical to
remove tool from service, then shut
off the air supply to the tool and write
or have written a warning note and
attach it to the tool.
—It tool is to be used with a balancer or
other suspension device, ensure that
the tool is firmly attached to the
suspension/support device.
— When operatingthe tool, alwayskeep
the body and particularly the hands
away from the working attachment
fixed to the tool.
—The tool is not electrically insulated.
Never use the tool if there js any
Model 5979A
1/8" (3 mm) Pencil Air Die Grinder
Use Of
Balancer Or Support
NO
bar 90
bar 90
PSI
A
WARNING
Always Read Instructions
Before Using Power Tools
AlwaysWear Safety
Goggles
WearHearing Protection
Avoid Prolonged Exposure
To Vbration
A1'Pipe And Fittings
Should Be 1/2' Or Larger
Compressor
with Sufficient C apacity
To Maintahl Recommended
Working Pressure At
Each Tool Outlet
Receiver Tank
40 Gallons Or More
Recommended A ir SupplySystem
Page No I
Important
Read theseinstructions carefullybeforeinstalling,operating,
servicingor repairingthis tool. Keeptheseinstructions in asafe
accessible place.
Product Type
1/8" (3 mm) Pencil
Air Die Grinder
Model No/Nos
5979A
Recommended Hose Bore
Size —Minimum
5/16 ins
8 mm
Noise Level:SoundPressureLevel 72.0dB(A)
Sound Power
Test M ethod: T estedin accordance with Pneurop
test code PN8NTC1 and ISO Standard 3744
Vibration Level
Test Method: Tested in accordance with ISO
standards 8662 Parts 1 & 13
chanceOfcomingintocontactwith liveelectricity.
— Always whenusingthetool,adoptafirmfootingand/or
positionandgripthe toolsufficientlyonlyto overcome
anyreactionforcesthatmayresultfromthe tool doing
work. Do not overgrip.
—Use only correct spare parts for maintenance and
repair.Do not improviseor maketemporaryrepairs.
Majorservicingandrepairsshouldonly becarriedout
by persons trained to do so.
—Do not lock, tape, wire, etc. the 'On/Off' valve in 'On'
position. The trigger/lever,etc. must always be free to
return to the 'Off' position when released.
— Alwaysshutoffthe air supplyto the toolandpressthe
'On/Off' valve to exhaust the air from the feed hose
beforefitting, removingor adjustingthe working
attachment fitted to the tool.
—Before usingthe tool, make sure that a shut off device
Take Air From Top
Easy To Reach And Air Tool
Operate Shut Off Valve
Air Regulator Set At
Recommended W orking
Air Pressure
Filter Lubricator
Drain Daily
Form # ZCE567A
Date 6-03/A
RPM
70,000
Cycles Per Min.
Serial No.
Recommended Max.
Hose Length
30 Ft
10 M
Level
84.0 dB(A)
2.0 Meters / Sec2
Low Spot TO
Trap Water
Drain Daily
Figure 1