GRAPHITE 58G020 Bedienungsanleitung Seite 9

• Do not change the direction of rotation of the tool spindle while it is
running. Failure to do so may damage the drill/driver.
• Use a soft, dry cloth to clean the drill/driver. Never use any
detergent or alcohol.
• Do not repair a defective unit. Repairs may only be carried out by
the manufacturer or an authorised service centre.
PROPER BATTERY HANDLING AND OPERATION
• The battery charging process should be under the control of the
user.
• Avoid charging the battery at temperatures below 0 C.
• Only charge the batteries with the charger recommended by
the manufacturer. The use of a charger designed to charge a
different type of battery poses a risk of fire.
• When the battery is not in use, keep it away from metal objects
such as paper clips, coins, keys nails, screws, or other small
metal items that can short-circuit the battery terminals. Short-
circuiting the battery terminals can cause burns or fire.
• In the event of damage and/or misuse of the battery, gases may
be released. Ventilate the room, consult a doctor in case of
discomfort. The gases may damage the respiratory tract.
• Fluid leakage from the battery may occur in extreme
conditions. Liquid leaking from the battery can cause irritation
or burns. If a leak is detected, proceed as follows:
- Carefully wipe off the liquid with a piece of cloth. Avoid contact of
the liquid with the skin or eyes.
- if the liquid comes into contact with the skin, the relevant area on
the body should be washed immediately with copious amounts of
clean water, or neutralise the liquid with a mild acid such as lemon
juice or vinegar.
- if the liquid gets into the eyes, rinse them immediately with plenty
of clean water for at least 10 minutes and seek medical advice.
• Do not use a battery that is damaged or modified.
Damaged or modified batteries may act unpredictably, leading
to fire, explosion or danger of injury.
• The battery must not be exposed to moisture or water.
• Always keep the battery away from a heat source. Do not
leave it in a high temperature environment for long periods of
time (in direct sunlight, near radiators or anywhere where the
temperature exceeds 50°C).
• Do not expose the battery to fire or excessive
temperatures. Exposure to fire or temperatures above 130°C
may cause an explosion.
NOTE: A temperature of 130°C can be specified as 265°F.
• All charging instructions must be followed, and the
battery must not be charged at a temperature outside the
range specified in the rating table in the operating
instructions. Charging incorrectly or at temperatures outside
the specified range can damage the battery and increase the
risk of fire.
BATTERY REPAIR:
• Damaged batteries must not be repaired. Repairs to the
battery are only permitted by the manufacturer or an
authorised service centre.
• The used battery should be taken to a disposal centre for
this type of hazardous waste.
SAFETY INSTRUCTIONS FOR THE CHARGER
• The charger must not be exposed to moisture or water.
The ingress of water into the charger increases the risk of
shock. The charger may only be used indoors in dry rooms.
• Unplug the charger from the mains before carrying out any
maintenance or cleaning.
• Do not use the charger placed on a flammable surface
(e.g. paper, textiles) or in the vicinity of flammable
substances. Due to the charger's temperature increase
during the charging process, there is a danger of fire.
• Check the condition of the charger, cable and plug each
time before use. If damage is found - do not use the
charger. Do not attempt to disassemble the charger. Refer
all repairs to an authorised service workshop. Improper
installation of the charger may result in a risk of electric shock
or fire.
• Children and physically, emotionally or mentally challenged
persons, as well as other persons whose experience or
knowledge is insufficient to operate the charger with all safety
precautions, should not operate the charger without the
supervision of a responsible person. Otherwise there is a
danger that the device will be mishandled resulting in injury.
• When the charger is not in use, it should be disconnected
from the mains.
• All charging instructions must be followed, and the
battery must not be charged at a temperature outside the
range specified in the rating table in the operating
instructions. Charging incorrectly or at temperatures outside
the specified range can damage the battery and increase the
risk of fire.
o
CHARGER REPAIR
• A defective charger must not be repaired. Repairs to the
charger are only permitted by the manufacturer or an
authorised service centre.
• The used charger should be taken to a disposal centre for
this type of waste.
ATTENTION: The device is designed for indoor operation.
Despite the use of an inherently safe design, the use of
safety measures and additional protective measures, there
is always a residual risk of injury during work.
Li-Ion batteries can leak, catch fire or explode if they are
heated to high temperatures or short-circuited. Do not store
them in the car during hot and sunny days. Do not open the
battery pack. Li-Ion batteries contain electronic safety
devices which, if damaged, can cause the battery to ignite
or explode.
Explanation of the used pictograms
Read the operating instructions and observe the warnings
1.
and safety conditions contained therein.
Wear safety goggles and ear protection.
2.
Keep children away from the appliance.
3.
Protect from rain.
4.
Indoor use, protected from water and moisture.
5.
Recycling.
6.
Second class of protection.
7.
Selective collection.
8.
Do not throw the cells into the fire.
9.
Posing a risk to the aquatic environment.
10.
Do not allow heat to exceed 50°C.
11.
CONSTRUCTION AND PURPOSE
The drill/driver is a battery-powered power tool. It is driven by a
brushless DC motor together with a planetary gearbox. The drill/driver
can be used in non-impact or impact mode. It is designed for
screwdriving and unscrewing screws and bolts in wood, metal, plastic
and ceramics, and for drilling holes in these materials in non-impact
mode. In impact mode, it is used for drilling in concrete, stone, brick,
etc. Cordless, cordless power tools are particularly suitable for
renovation and construction work, carpentry and interior fittings, room
adaptations and all work in the area of DIY (do-it-yourself).
Do not misuse the power tool.
DESCRIPTION OF THE GRAPHIC PAGES
The numbering below refers to the components of the unit
shown on the graphic pages of this manual.
Quick-action chuck
1.
5