Using The Jump Starter In Standard Mode; Using The Jump Starter In Override Mode - Ryobi Rjsc18 Bedienungsanleitung

BATTERY PACK SAFETY WARNINGS
■ To reduce the risk of fire, personal injury, and
product damage due to a short circuit, never
immerse the product, battery pack, or charger in
fluid or allow fluid to flow inside them. Corrosive
or conductive fluids, such as seawater, certain
industrial chemicals, and bleach or bleach-
containing products, etc., can cause a short circuit.
■ Use the product only with battery packs specified
in this manual. The use of any other battery packs
may create a risk of injury and fire. When using a
battery-operated product, basic safety precautions
should always be followed to reduce the risk of fire,
leaking batteries, and personal injury. Do not mix
battery packs of different types or levels of use.
■ Recharge the battery pack only with the
charger specified by the manufacturer. A
charger that is suitable for one type of battery
pack may create a risk of fire when used with
another battery pack. Remove the battery
pack from the product before recharging.
■ Follow all charging instructions and do not
charge the battery pack or product outside the
temperature range specified in the instructions.
Charging improperly or at temperatures
outside the specified range may damage the
battery and increase the risk of fire.
■ Do not expose a battery pack or product to fire
or excessive temperatures. Exposure to fire or
excessive temperature above 130 °C may cause
explosion.
■ When the battery pack is not in use, keep it
away from other metal objects, such as paper
clips, coins, keys, nails, screws, or other small
metal objects that can make a connection
from one terminal to another. Shorting the
battery pack terminals together may cause
sparks, burns, fire, or an explosion.
■ Under abusive conditions, liquid may be ejected
from the battery pack; avoid contact. If contact
accidentally occurs, flush with water. If liquid
contacts eyes, seek medical help. Liquid ejected
from the battery pack may cause irritation or burns.
■ Do not use a battery pack or product that is
damaged or modified. Damaged or modified
batteries may exhibit unpredictable behaviour
resulting in fire, explosion, or risk of injury.
■ Do not dispose of battery packs together
with household waste material. They must
be collected separately and returned to an
environmentally compatible recycling facility.
Check with your local authority or retailer for
recycling advice and collection point.
■ Do not recharge primary cells (non-rechargeable).
8
OPERATION
Read and understand
operating instructions regarding cautions and
recommendations before jump starting the vehicle.
JUMP STARTER MODES
■ Standard mode
The standard mode can be used to supply
–
electrical power to discharged vehicle batteries.
NOTE: If the jump starter encounters an error
during the standard mode, the vehicle battery
may be deeply discharged.
■ Override mode
The override mode is required when
–
the voltage level of the vehicle battery is
insufficient to jump start the vehicle using
the standard mode.
NOTE: Use the override mode only when the
jump starter fails to prime the vehicle battery
using the standard mode.
USING THE JUMP STARTER IN STANDARD
MODE
1. Power off all power loads in the vehicle.
2. Connect the positive (red) clamp to the
positive (+) battery terminal.
3. Connect the negative (black) clamp to the
negative (-) battery terminal or vehicle chassis.
NOTE: Do not allow positive and negative
battery clamps to touch or connect to each
other to avoid sparking.
4. Press and hold the on/off button for two
seconds to power on the product.
NOTE: The power LED turns solid green.
5. Press the prime button to charge the product.
NOTE: When the product is priming the
vehicle battery, the LED will flash yellow.
6. Once primed, the start engine LED turns
solid green.
7. Start the vehicle.
NOTE: If the engine fails to start, review the
troubleshooting guide for further instructions.
Additional service on your vehicle may be
required; seek professional assistance.
8. Press and hold the on/off button for two
seconds to power off the product.
9. Disconnect the product from the vehicle by
removing the negative (black) clamp first,
then the positive (red) clamp.
USING THE JUMP STARTER IN OVERRIDE
MODE
WARNING! Use the override mode with extreme
caution and care. Spark prevention and reverse
polarity protections are disabled in override mode.
your vehicle's