Electrolux ADU 3040 N Einbauanleitung Seite 3

a horizontal line through the vertical line
at 772 mm above the height of the
hotplate. Measure 284 mm either side of
the vertical line for the 600 mm wide hood
or 434 mm either side of the vertical line
for the 900 mm wide hood.
B mm 600
A mm 284
B = Width of the cooker hood in mm
A = Distance between the centres of the
holes and the centre of the hood.
3 - Fixing the wall brackets item 2.
a - Place one of the two wall brackets item 2
(fig. 1) 15 mm from the ceiling or from
a horizontal line drawn between the top
of the adjoining wall cabinets, ensuring
that the bracket is level and mark the
centre for the key hole bracket fixing
screws.
b - Mark on the wall the centres of the two
keyholes of the bracket.
c - Place the other wall bracket item 2 fig. 1
on the wall at "X"; this measurement
should be determined by the height of the
upper chimney stack and mark the centres
for the key hole bracket fixing screws.
4 - Pilot drill all the hole positions as marked on
the wall using a Ø 8 mm drill and fix the wall
brackets items 1-2 using the Ø 8 mm rawl
plugs and screws supplied.
5 - Splashback (optional)
When the splashback is to be fitted, the
distance between the cooker hood and the
cooking appliance will be determined by the
height of the splashback item F. The
splashback should be fitted before installing
the canopy. If the splashback is to be fixed to
the wall using the top and bottom fixing holes,
care must be taken to ensure that the
splashback is fitted at the correct height before
fixing it into position. The fitting should be
undertaken by a competent person, with
experience in this type of instal-lation.
If the splashback is to be fixed using only the
top fixing holes, proceed as follows:
a - Place the splashback on the worktop as
illustrated in fig. 2a, then holding it
against the wall ensuring that it is correctly
posi-tioned on the worktop mark the holes
for the top fixing screws on the wall.
b - Pilot drill the wall using a 8 mm Ø drill
and fix the splashback using the Ø 8 mm
rawl plugs and screws supplied.
c - If the fixing holes in the bottom of the
splashback are not to be used to secure
the splashback to the wall the installer
should ensure that the bottom flange is
tucked down behind the rear of the
worktop.
900
434
Installation type C (fig. 3)
This type of installation can be carried out
using only the U-shaped lower chimney item
I.
1 - Draw a vertical line on the wall from the
centre of the cooking appliance up to the upper
limit which could be a wooden shelf: this is
to ensure the correct vertical alignment of the
wall fixing brackets.
Measure down the vertical line from the top
of the adjoining wall cabinets and draw a
horizontal line at 478 mm through the vertical.
2 - Fixing the wall brackets item 1
Mark the fixing holes for the brackets on the
horizontal line as shown in the paragraph 4.1
2.
3 - Fixing the wall brackets item 2
a - Place one of the two wall brackets item 2
(fig. 1) 15 mm from the ceiling or from
a horizontal line drawn between the top
of the adjoining wall cabinets, ensuring
that the bracket is level and mark the
centres for the key hole bracket fixing
screws.
b - Mark the centres for the two key hole
fixing bracket screws on the wall.
4 - Pilot drill all the centres using a Ø 8 mm drill
and fix the wall brackets items 1-2 using Ø 8
mm rawl plugs and screws supplied.
4.2 - Fixing the canopy hood
1 - Hook the canopy hood item C onto the wall
fixing brackets ensuring that the security fixing
screws align with the holes in the centre of
the back panel of the cooker hood as illustrated
in fig. 4.
2 - Adjust the canopy item C horizontally by
rotating the screws item R inside the cooker
hood (fig. 5).
3 - Fix the cooker hood to the wall brackets item
1 using two nuts and two washers supplied.
4.3 - Electrical connection and working test
1 - The safety measures contained in paragraph 3
are to be strictly observed.
2 - Once the electrical connection has been com-
pleted, check that worktop illumination, motor
and speeds work properly.
4.4 - Ducting or recirculation fitting
1 - Ducting fitting (Installation type A/B)
a - The cooker hood can be ducted to the
out-side using either rigid or flexible fire
retar-dant ducting Ø 100 or 120 mm. The
choice should be left to the installer.
b - The ducting spigot is provided with an
air outlet of 100 mm.
When Ø 120 mm ducting is to be used it
will be necessary to convert the 100 mm
ducting spigot by cutting along the dotted
3