mm. The battery rated voltage and capacity is 3.59
V/5500 mAh.
For long-term storage of the battery, make sure it is
fully charged every half year to ensure the battery quality.
Otherwise, damage may occur.
The purchased batteries by users need to comply with
the relevant international standards about battery safety
(e.g. EN/IEC standards).
The built-in battery cannot be dismantled. Please
contact the manufacture for repair if necessary.
Make sure the battery temperature is between 0°C to
50°C (32°F to 122°F) when charging.
Confirm there is no flammable material within 2 m of
the charger during charging.
Batteries of improper size cannot be installed, and
may cause abnormal shutdown.
CAUTION: Risk of explosion if the battery is replaced
by an incorrect type. Replace with the same or equivalent
type only.
Improper replacement of the battery with an incorrect
type may defeat a safeguard (for example, in the case of
some lithium battery types).
Do not dispose of the battery into fire or a hot oven, or
mechanically crush or cut the battery, which may result
in an explosion.
Do not leave the battery in an extremely high
temperature surrounding environment, which may result
in an explosion or the leakage of flammable liquid or
gas.
Do not subject the battery to extremely low air
pressure, which may result in an explosion or the leakage
of flammable liquid or gas.
Dispose of used batteries according to the
instructions.
DO NOT place the battery in the reach of children.
DO NOT swallow the battery to avoid chemical burns.
This product contains a coin/button cell battery. If the
coin/button cell battery is swallowed, it can cause severe
internal burns in just 2 hours and can lead to death.
If the battery compartment does not close securely,
stop using the product and keep it away from children.
If you think batteries might have been swallowed or
placed inside any part of the body, seek immediate
medical attention.
DO NOT place the device with battery or the battery
alone near heating or fire source. Avoid direct sunlight.
Maintenance
If the product does not work properly, please contact
your dealer or the nearest service center. We shall not
assume any responsibility for problems caused by
unauthorized repair or maintenance.
Make sure that the power has been disconnected
before device teardown and repair by professionals.
Check the optical surfaces of objective lens, eyepiece,
rangefinder, etc. If necessary, remove dust and sand
from the optics using tools and solvent designed
especially for this purpose (it is preferable to use a non-
contact method).
Wipe the exterior surfaces of metal, plastic and
silicone parts with a clean and soft cloth. Do not use
chemically active substances, solvents, etc. as these
may damage the paint.
Clean the electrical contacts of the battery on the
device using a non-greasy organic solvent.
If the equipment is used in a manner not specified by
the manufacturer, the protection provided by the device
may be impaired.
Using Environment
Make sure the running environment meets the
requirement of the device. The operating temperature
shall be -30°C to 55°C (-22°F to 131°F), and the operating
humidity shall be from 5% to 95%.
DO NOT expose the device to high electromagnetic
radiation or dusty environments.
DO NOT aim the lens at the sun or any other bright
light.
Place the device in a dry and well-ventilated
environment.
Avoid equipment installation on vibratory surface or
places subject to shock (neglect may cause equipment
damage).
This equipment is not suitable for use in locations
where children are likely to be present.
Emergency
If smoke, odor, or noise arises from the device,
immediately turn off the power, unplug the power cable,
and contact the service center.
Laser
out. The laser radiation emitted from the device can
cause eye injuries, burning of skin or inflammable
substances. Before enabling the laser ranging function,
make sure no human or inflammable substances are in
front of the laser lens. Do not place the device where
minors can fetch it. According to IEC 60825-1:2014, EN
60825-1:2014+A11:2021, and EN50689: 2021, this laser
product is classified as Class 1 laser product and
consumer laser product.
Limited Warranty
Scan the QR code for the product warranty policy.
Manufacture Address
Room 313, Unit B, Building 2, 399 Danfeng Road, Xixing
Subdistrict, Binjiang District, Hangzhou, Zhejiang 310052,
China
Hangzhou Microimage Software Co., Ltd.
COMPLIANCE NOTICE: The thermal series products
might be subject to export controls in various countries
or regions, including without limitation, the United States,
European Union, United Kingdom and/or other member
countries of the Wassenaar Arrangement. Please consult
your professional legal or compliance expert or local
government authorities for any necessary export license
requirements if you intend to transfer, export, re-export
the thermal series products between different countries.
Behördliche Informationen
Diese Bestimmungen gelten nur für Produkte, die das
entsprechende Zeichen oder die entsprechenden
Informationen tragen.
Erklärung zur EU-Konformität
Dieses Produkt und – gegebenenfalls – das
mitgelieferte Zubehör tragen das „CE"-
Kennzeichen und entsprechen daher den
geltenden harmonisierten europäischen
Normen, die in der Richtlinie 2014/30/EU (EMV), der
Richtlinie 2014/35/EU (NSR), der Richtlinie 2011/65/EU
(RoHS) und der Richtlinie 2014/53/EU (RED) aufgeführt
sind.
Hiermit erklärt Hangzhou Microimage Software Co., Ltd.,
dass dieses Gerät (siehe Etikett) mit der Richtlinie
2014/53/EU übereinstimmt.
Der vollständige Text der EU-Konformitätserklärung ist
unter der folgenden URL-Adresse einsehbar:
https://www.hikmicrotech.com/en/support/download-
center/declaration-of-conformity/
Frequenzbänder und Leistung (für CE)
Die für das folgende Funkgerät geltenden
Frequenzbänder und die nominalen Grenzwerte für die
Sendeleistung (gestrahlt und/oder leitungsgeführt) sind
wie folgt:
WLAN 2,4 GHz (2,4 Ghz bis 2,4835 GHz) 20 dBm
WLAN 5 GHz (5,15 bis 5,25 GHz): 23 dBm
Verwenden Sie bei einem Gerät ohne mitgeliefertes
Netzteil nur ein Netzteil von einem zugelassenen
Hersteller. Detaillierte Angaben zum Strombedarf finden
Sie in der Produktspezifikation.
Verwenden Sie bei einem Gerät ohne mitgelieferte
Batterien nur Batterien/Akkus von einem zugelassenen
Hersteller. Detaillierte Angaben zu den Batterie-/Akku-
Anforderungen finden Sie in der Produktspezifikation.
111
When any laser
equipment is in use,
make sure that the
device lens is not
exposed to the laser
beam, or it may burn
Deutsch